User manual KUSSMAUL 091-92-12

[. . . ] FILE: IM_091-92-12_Rev_B DATE: 09-15-04 INSTRUCTION MANUAL BATTERY SAVER LOW RIPPLE POWER SUPPLY / AUTOMATIC LOAD SWITCH FOR 12VDC VEHICLE SYSTEMS MODEL #091-92-12 INPUT: 115 VOLTS, 50/60 Hz AC, 1. 8 amps. RMS OUTPUT: 13. 2VDC, 10 AMPS DC, 130VA 3 YEAR WARRANTY KUSSMAUL ELECTRONICS CO. , INC. 170 CHERRY AVE. , WEST SAYVILLE, N. Y. 11796-1221 TEL: in NY 631-567-0314 TOLL FREE: 800-346-0857 FAX: 631-567-5826 INTRODUCTION The 091-92-12 BATTERY SAVER is a power supply with a load power transfer function. [. . . ] The low voltage connections are made through the DC output connector as shown in INSTALLATION WIRING DIAGRAM, FIGURE 1. Connect terminal 1 to the vehicle's 12 volt battery (+). Connect terminal 3 to the +12 volt electrical loads. Connect terminal 4 to the vehicle ground or to the battery (-). Loads connected to the Battery Saver will be powered from the vehicle battery when the AC power to the Battery Saver is OFF and from the Battery Saver power supply when the AC power is ON. TEST and OPERATION The 091-92-12 Battery Saver system interface panel contains two (2) Green LEDs as follows: Refer INSTALLATION WIRING DIAGRAM, Figure 1. "LOAD POWER" LED: Illuminates when power is being supplied to the load(s) regardless of the source of the power (Vehicle Battery or Battery Saver). "BATT SVR PWR" LED: Illuminates when Battery Saver is receiving AC power and the power supply internal to the Battery Saver is ON and functioning. Installation Test 1. Remove AC power from the 091-92-12 Battery Saver. Verify "LOAD POWER" LED is illuminated and loads are being powered by vehicle battery (voltage at load is approximately equal to vehicle battery terminal voltage). Apply AC power to 091-92-12 Battery Saver and verify: 1. "LOAD POWER" LED remains illuminated 2. "BATT SVR PWR" LED illuminates approximately five (5) seconds after application of AC power to Battery Saver. Load voltage is between 13. 2VDC and 13. 4VDC Operation The 091-92-12 Battery Saver contains special circuitry that eliminates power delivery "glitches" or interruptions during load power transfer(s) from: *Vehicle Battery to Battery Saver: Five (5) second delay as Battery Saver power supply stabilizes. *Battery Saver to Vehicle Battery: No delay The MINIMUM voltage at the load during any power transition is: Vehicle Battery VDC - 1. 3VDC for a MAXIMUM of 150 milli-seconds (. 150 seconds). INSTALLATION PRECAUTIONS Refer Figure1, INSTALLATION WIRING DIAGRAM and Specifications & Outline The 091-92-12 Battery Saver is AC Input AND DC Output over-current protected as follows: 115VAC 60Hz Input: 5 Ampere DC Output: ATC, 10 Ampere The ATC 10 Ampere DC OUTPUT FUSE internal to the Battery Saver is common to both the Battery Saver Power Supply output AND the vehicle battery connection that supplies power to the load when the Battery Saver is OFF (115VAC to Battery Saver - OFF). Current OVERLOADING the Battery Saver in excess of 10 Amperes will: Initiate current limiting of the Battery Saver Power Supply with a corresponding reduction of the Battery Saver Power Supply terminal voltage when the Battery Saver is ON until the DC OUTPUT FUSE open circuits. [. . . ] Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped. shall have no liability for damages of any kind to associated equipment arising from the installation and /or use of the Kussmaul Electronics Company, Inc. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees or others. [. . . ]