User manual KVH 01027702BK INSTALL

[. . . ] TracVision A7 Installation Guide TracVision A7 Installation Guide ­ ADDENDUM TracVision A7 Installation Guide Addendum ECO #7719 The following information applies to Revision A of the TracVision A7 Installation Guide (KVH Part Number 54-0350). Mounting the Antenna - Roof Mount Kit The parts and procedure for mounting the TracVision A7 directly to the roof have changed. This addendum explains this different procedure. With an assistant's help, position the antenna onto the center of the vehicle's roof with a rubber mounting block under each bracket. WARNING PLEASE READ - IMPORTANT!The roof mount kit is designed for mounting the antenna to a flat metal roof up to 3/16" thick. [. . . ] Call KVH at 401-847-3327 to order the Spacers Kit (P/N 72-0221). Spacer installation instructions are provided on page 2. 10. 9. Seal all fasteners with silicone sealant or equivalent. 10. Place the rubber mounting blocks back onto the mounting plates. Place the antenna onto the mounting blocks. Align the holes in the antenna brackets with the holes in the mounting blocks. 2. 9 54-0350 TracVision A7 Installation Guide Spacer Installation Instructions ­ If Necessary in Step 5 If spacers are needed to raise the antenna off the roof, follow the steps below to install a spacer under each bracket*: a. Remove the #8-32 x 3/8" screws and washers securing the factory-installed plastic spacer to the metal bracket. Adding Spacers (If Needed for Extra Height) Bracket New Spacer b. Insert a second spacer from the kitpack between the original spacer and the bracket. Secure both spacers to the bracket using the #8-32 x 7/8" screws supplied in the kitpack and the original washers that you removed in Step a. Place a rubber spacer onto the end of each rubber mounting block. Factory-installed Spacer Flat Washer Lock Washer #8-32 Screw Bracket Plastic Spacer Rubber Spacer * Requires Spacers Kit (KVH P/N 72-0221). Mounting Block 2. 10 54-0350 Installing the Antenna 12. At each bracket, insert two of the supplied 1 /4"-20 hex socket screws through the antenna bracket and mounting block and into the mounting plate's nut bar. If you added a spacer as explained on page 2. 10, use the 21/2" screws supplied in the Spacers Kit. Otherwise, use the 21/4" screws supplied in the roof mount kit. Tighten the screws to secure in place. Securing the Antenna to the Roof Cover 13. Flip down the skirt on each rubber mounting block to hide the mounting plates. Attach a protective cover onto each bracket. The covers simply snap into place at the sides of the brackets. Two different sizes of covers are provided in the kitpack. Install the two larger covers on the rear brackets and the smaller covers on the front brackets. Attaching the Cover Hex Socket Screws Antenna Bracket Mounting Block Nut Bar Mounting Plate Vehicle Roof Proceed to Section 2-5 on page 2. 16. 2. 11 54-0350 TracVision A7 Installation Guide 2-4 Mount the Antenna Hummer® Mount Kit 3. Remove the long rubber strips that run along the top of the crossbars. Be sure to save these strips for future use. At each crossbar, insert two T-nuts into the center channel and slide the nuts along the channel. Inserting T-nuts in Crossbar Center Channel Center Channel If you are mounting the antenna to a Hummer roof rack, follow the appropriate steps in this section for your particular Hummer model: Hummer H2 . [. . . ] Within a few minutes, all three status lights on the front of the receiver should be lit green. If any of these lights are not green, refer to Section 10-4, "System Status Lights, " in the User's Guide for troubleshooting details. Receiver Status Lights 5. A progress bar will appear on the TV, indicating that the receiver is downloading the program guide. Once the guide is loaded, verify that you can view the DIRECTV preview channel (100). Program Guide Load Progress Bar If your satellite dish is ready for DIRECTV® service, please wait until your Advanced Program GuideTM is prepared. Installation Status Lights Acquiring guide data. . . Only the DIRECTV® preview channels (such as channels 100 and 201) are viewable until the owner activates the receiver. 4. 6 54-0350 Completing the Installation 4-3 Educate the Customer · Be sure to give the manuals to the owner and explain how to use the product. [. . . ]