User manual KYOCERA DU-21

[. . . ] EN 55 022:1998 Class B EN 50 082-1:1997 IEC 801-2:1991 IEC 801-3:1984 IEC 801-4:1988 EN 60 950:1992+A1+A2+A3+A4 The manufacturer and its merchandising companies retain the following technical documentation in anticipation of the inspection that may be conducted by the authorities concerned. ) Description of device: This Page Printer Model FS-1750 is the 14ppm; up to A4 size plain paper, laser, dry toner etc. The printer can be equipped with several enhancement optional units such as the Paper Feeder PF-21, Duplexer DU-21 etc. AS/NZS 3548:1995 (CISPR 22:1993 Class B) IEC60 950:1991+A1+A2+A3+A4 (EN 60 950:1992+A1+A2+A3+A4) The manufacturer and its merchandising companies retain the following technical documentation in anticipation of the inspection that may be conducted by the authorities concerned. [. . . ] Press the + or - key until the display shows the desired binding type. If you want to abandon the duplex mode selection procedure, press the CANCEL key now. CMNT Initiates a PRESCRIBE command sequence; RES; CMNT Causes a page break and resets parameters; DUPX 2; CMNT Selects duplex mode, short-edge binding; SPO P; CMNT Selects portrait orientation; STAK 1; CMNT Select face-down delivery; EXIT; This text prints rightside-up on the front side of the page. This section explains how to handle paper jams in the duplexer and respond to error messages. Paper jam In the event of a paper jam, the Paper jam message appears on the printer's message display. Note When clearing jams, check other option units (the paper handler/stacker, paper feeder, sorter, and bulk paper stacker) for jammed paper before pulling out the DU-21's duplexer drawer. To check for other option units for jams, open their rear covers. If paper jams inside the duplexer, the READY indicator flashes on the duplexer's indicator panel. To clear the jam, first check other option units for paper by opening their rear covers. then pull the duplexer drawer part-way open. If paper is visible under the clear plastic cover, open the cover and remove the paper as shown in Figure 11(a). If the paper is stuck inside the duplexer, turn the knob on the left side of the duplexer drawer counterclockwise [see Figure 11(b)] to move the paper out of the duplexer. If the paper jams at the rear of the duplex unit, open the rear cover and remove it. Whenever you clear a jam, be sure to check inside other option units, as well as inside the duplexer drawer and the duplexer's rear cover. After clearing the jam, reclose the drawer, open and close the printer's top cover or the paper feed unit. Then the printer automatically warm up, goes on-line, and continue printing. Depending on the part at which the jam occurred, the printer may or may not print the jammed page. Error message If the printer's message display shows Duplex unit front cover Open or Duplex unit rear cover Open, check the front/rear covers and ensure that they are securely closed. When using duplex printing, the image on the reverse side of the paper may be slightly out of alignment with that on the front side. If this occurs, the image position can be adjusted either to the left or right by about 2 mm. When using the duplex unit, the reverse side of the paper (the second page) is printed first, followed by the front side (the first page). Adjustment of the print position affects only the image printed on the front side of the paper; i. [. . . ] All paper used in the duplexer and the printer should be long grain. Other paper properties Porosity: Refers to the density of the paper structure; that is, to how openly or compactly the fibers are bonded. Stiffness: Limp paper can buckle inside the duplexer and the printer, while paper that is too stiff may bind. Most paper also has a top and bottom surface. [. . . ]