Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual KYOCERA FS-1000. We hope that this KYOCERA FS-1000 user guide will be useful to you.
Lastmanuals help download the user guide KYOCERA FS-1000.
Detailed instructions for use are in the User's Guide.
[. . . ] Table of Contents
Page Printer
User's Manual
Caution
NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.
Notice on Software
SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The printer is factory-set to emulate the PCL. The emulation mode can be changed by following the procedures described in Chapter 1.
Notice
The information in this manual is subject to change without notification. Additional pages may be inserted in future editions. [. . . ] After a few moments, the Kyocera Mita Digital Library main menu appears. Click on Install Drivers to start dirver installation.
If this screen does not appear, click the Windows Start button and select Run. Enter the following: [CD drive letter]:\setup
Click the OK button. After a few moments, the Kyocera Mita Digital Library main menu appears.
2-2
Printing From Applications
2. 2
Printing From Applications
This section uses a document created using Microsoft Word as an example of how to print from applications. When feeding from the paper cassette, do not insert paper into the MP tray. Because the MP tray default setting is set to first mode (priority printing from the MP tray), if there is paper inserted in the MP tray, the first paper will always feed from there. To change the MP tray's first mode setting, send the PRESCRIBE FRPO T0 command to the printer from the Remote Operation Panel utility. (See section 1. 6. 7. ) For FRPO commands, refer to the Programming Manual provided on the CD-ROM supplied with the printer.
Note
1 2 3
Set paper of the size specified for the document in the application into the printer's paper cassette. (For details on how to set paper sizes, refer to the Installation Manual. ) Set the paper size inserted into the paper cassette in the Remote Operation Panel utility (see page 1-18). If paper size settings are not the same, print may be incorrectly positioned. Create the print document, then click File from the menu bar. Next, click Print, and the Print dialog box will appear.
Application drop-down menu
Print dialog box
2-3
Printing From Applications
4
Click the Properties button in the Print dialog box. The Properties dialog box is displayed.
Properties button Properties dialog box
5
Click the paper size icon in the Paper Size list box so that it is greyed, then click the OK button. A5 was selected for the following example.
A5 size
2-4
Printing From Applications
6
Once you finish making paper size settings, the Print dialog box is displayed again. Click the OK button to start printing.
Note
Settings made from applications are not saved when the application is closed, and default settings are restored when the application is opened the next time. To change the printer driver default settings, make printer settings from Windows.
2. 2. 1
Feeding from the MP tray
First mode (priority printing) is set in the MP tray default settings. To change the MP tray's first mode setting, send the PRESCRIBE FRPO T0 command (!R!FRPO T0, 0; EXIT;) to the printer from the Remote Operation Panel utility (see section 1. 6. 7). For FRPO commands, refer to the Programming Manual provided on the CD-ROM supplied with the printer.
2-5
Printing From Applications
2. 2. 2
Custom Size Settings
This printer can feed non-standard paper sizes. The paper cassette can accommodate sizes ranging from 148 to 216 mm in width and 216 to 297 mm in length, and the MP tray can accommodate sizes ranging from 80 to 216 mm in width and 148 to 297 mm in length. The procedure for setting custom sizes from the printer driver is explained below.
1
Display the printer driver's Properties dialog box from the application software, then click Custom from the Paper Size list box so that it becomes greyed.
Custom size Paper Size list box
2
Click the Custom Size button to display the Custom Paper Size dialog box.
Custom Size button Custom Paper Size dialog box
2-6
Printing From Applications
3
Enter a name for your custom size and click the Add button.
Name settings Add button Units Paper size
4 5 6
Select the unit or measurement, Inches and Millimeters. Enter the height and width of the custom size in Size. [. . . ] The contents of the CD-ROM include manuals, printer drivers, and various utilities.
Face-up tray
This is located at the rear of the printer. Select paper output to the face-up tray when printing on postcards, envelopes, or labels.
Kyocera Mita PrintMonitor
This is a network management tool that can be used with the Kyocera FS series. You can view information for printers connected to the network using SNMP commands. Kyocera Mita PrintMonitor is contained on the Kyocera Mita Digital Library CD-ROM supplied with the printer.
E-2
Glossary
MB (mega byte)
This unit is used to express data quantities and memory capacities. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KYOCERA FS-1000
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual KYOCERA FS-1000 will begin.