User manual KYOCERA FS-1020

[. . . ] FS-1020D Page Printer Operation Guide Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The printer is factory-set to emulate the PCL. The emulation mode can be changed by following the procedures described in Chapter 1 . Notice The information in this manual is subject to change without notification. Additional pages may be inserted in future editions. [. . . ] FRPO FRPO is a PRESCRIBE command that permanently changes the printer's internal parameters. Each parameter is represented by two letters, such as R4 for default paper source, succeeded by FRPO, then followed by a value. For example, FRPO R4, 1; means that the default paper source (R4) is the printer's cassette (1). To confirm the current value for an FRPO parameter: 1 2 1 2 3 Enter the parameter (for example R4) in FRPO. The current value is shown in Value. To change the value for an FRPO parameter: Follow the above procedure to display the current value in Value. Erase the current value and enter the new value. For example, to change the default paper source to the MP Tray in the above example, enter 0 instead of 1 in Value. The value is changed. 1-58 Chapter 2 Maintenance 2 This chapter explains how to replace the toner container and how to clean parts such as the registration roller and charger wire. This chapter explains the following topics: · Toner Container Replacement · Cleaning the Printer 2-1 Toner Container Replacement 2. 1 Toner Container Replacement When the printer runs low on toner, the (toner) indicator flashes on the operator panel. Be sure to promptly replace the toner container and clean the inside of the printer when this message appears. If the printer stops printing while the toner container to continue printing. (toner) indicator is lit, replace the 2. 1. 1 Toner Container Replacement Interval Assuming an average toner coverage of 5%, with EcoPrint mode turned off the toner container will need replacing approximately once every 7, 200* printed pages. * In the case of a new printer in which a toner kit has been installed for the first time, the number of copies that can be printed will be approximately 4, 000. Toner Kit to be Used Name: TK-18 Description: Toner container Wiper cloth Plastic bag Installation Guide (The kit supplied with the printer only contains the toner container and wiper cloth. ) · Be sure to distance items such as floppy disks during toner container replacement. Be sure to clean the inside of the printer when replacing the toner container. For details, see section 2. 2 Cleaning the Printer on page 26. Use of original Kyocera Mita toner kits is highly recommended to prevent printer trouble and ensure the long life of the printer. Note · · 2-2 Toner Container Replacement 2. 1. 2 Replenishing Toner 1 Open the printer's top cover. Top Cover Figure 2-1 2 Pull lock lever #1 to the release (UNLOCK) position, then pull lock lever #2 to the release (right) position. Lock Lever #2 Lock Lever #1 Figure 2-2 3 Gently remove the old toner container. Put it in the supplied plastic bag and dispose of it. Plastic Bag Figure 2-3 2-3 Toner Container Replacement 4 Take the new toner container from the bag. Hold it with the protective seal (orange-colored) facing up. Shake the toner container horizontally at least 5 times. This ensures that the toner is evenly distributed inside. New Toner Container Figure 2-4 5 Carefully remove the protective seal (orange-colored). Protective Seal Figure 2-5 2-4 Toner Container Replacement 6 Install the new toner container in the printer. [. . . ] The printer has one expansion slot, and you can install a 8 MB, 16 MB, 32 MB, 64 MB, 128 MB, or 256 MB DIMM (Dual Inline Memory Module). Contact your Kyocera Mita dealer to purchase the DIMM that is best suited for use with this printer. KPDL (Kyocera Printer Description Language) This is Kyocera Mita's version of Adobe PostScript 3. First mode This is an operation mode for the MP tray. Because the MP tray default setting is set to first mode (priority printing from the MP tray), if there is paper inserted in the MP tray, the first paper will always feed from there even if another paper source is selected. First mode is specified as the factory default, but you can change this setting from the KM-NET Remote Operation Panel. MB (mega byte) This unit is used to express data quantities and memory capacities. [. . . ]