User manual KYOCERA FS-1100

[. . . ] OPERATION GUIDE FS-1100 FS-1300D This Operation Guide is for models FS-1100 and FS-1300D. Note This Operation Guide contains information that corresponds to using both the inch and metric versions of these machines. The inch versions of these machines are shown in the screens in this guide. If you are using the metric version, use the messages provided for the inch version as reference only. [. . . ] Paper source Paper Type Paper Cassette Yes No Yes No Yes Yes No Yes Yes Yes Yes No No No Yes Yes Paper Weight Range 64 to 90g/m2 Transparency 75 to 90g/m 2 MP tray Duplex path (MP tray available only Display in Status in Cassette mode) Monitor Normal2 Extra Heavy Normal2 Heavy1 Normal3 Normal2 Light Normal3 Normal3 Normal3 Normal2 Heavy3 Heavy3 Heavy3 Normal2 Normal2 Yes No Yes No Yes Yes No Yes No Yes Yes No No No Yes Yes Plain Transparency Preprinted Labels Bond Recycled Vellum Rough Letterhead Color Prepunched Envelope Cardstock Thick High quality Custom 1 (to 8) * Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 105 to 135g/m2 90 to 105g/m2 2 75 to 90g/m Less than 64g/m2 90 to 105g/m2 75 to 90g/m2 75 to 90g/m2 75 to 90g/m2 135 to 170g/m2 135 to 170g/m 135 to 2 170g/m2 75 to 90g/m2 75 to 220g/m2 Yes: Can be stored *. No: Cannot be stored This is a paper type defined and registered by the user. Up to eight types of user settings may be defined. User can also enable or disable the duplex path when using Custom. For more information, refer to Status Monitor on page 3-10. 2-10 Loading Paper Preparing the Paper After removing paper from the packaging, fan through the sheets to separate them prior to loading. If using paper that has been folded or is curled, straighten it prior to loading. Failure to do so may result in a paper jam. IMPORTANT Ensure paper is not stapled and clips are removed. Loading Paper into Cassette 250 sheets of 11 × 8 1/2" or A4 paper (80 g/m²) may be loaded into the Cassette. 1 Pull the cassette completely out of the printer. IMPORTANT When pulling the cassette out of the printer, ensure it is supported and does not fall out. 2 Press the bottom plate down until it locks. Loading Paper 2-11 3 Adjust the position of the width guides located on the left and right sides of the cassette. Press the release button on the left guide and slide the guides to the paper size required. Note Paper sizes are marked on the cassette. 4 Adjust the paper length guide to the paper size required. If you are going to use paper that is longer than A4, pull out the extension paper cassette by pushing the release lever one by one and adjust it to the desired paper size. 5 Load the paper in the cassette. Ensure the side to be printed is facing down and the paper is not folded, curled, or damaged. 2-12 Loading Paper Note Do not load paper above the triangle mark located on the width guide. 6 Insert the paper cassette into the slot in the printer. Push it straight in as far as it will go. There is a paper gauge on the left side of the front of the paper cassette to indicate the remaining paper supply. When paper is exhausted, the pointer will go down to the level of (empty). 7 Specify the paper size and type for the cassette using Configuration Tool. For more information, refer to Configuration Tool on page 3-14. Loading Paper 2-13 Loading Paper into MP (Multi-Purpose)Tray FS-1300D can load 50 sheets of 11 × 8 1/2" or A4 paper (80 g/m²) into the MP Tray. On the other hand, FS-1100 can one sheet into the Manual Feed. FS-1100 1 Pull the MP tray towards you until it stops. . IMPORTANT When pulling the cassette out of the printer, ensure it is supported and does not fall out. FS-1300D FS-1100 2 Adjust the position of the paper guides on the MP tray. Standard paper sizes are marked on the MP tray or Manual Feed. For standard paper sizes, slide the paper guides to the corresponding mark. FS-1300D 3 Pull out the subtray (for FS-1300D only). 2-14 Loading Paper FS-1100 4 Align the paper with the paper guides and insert as far as it will go. Note Do not load more paper than exceeds the tab of the MP tray (for FS-1300D only). FS-1300D Note If the paper is considerably curled in one direction, for example, if the paper is already printed on one side, try to roll the paper in the opposite direction to counteract the curl. Printed sheets will then come out flat (for FS-1300D only). Correct Incorrect Loading Paper 2-15 Correct When loading envelope, place with the envelope flap closed and keep the printing side face-up. Insert envelope against the guide with the flap on the front or left side until they stop. Correct Incorrect 5 Specify the paper size and type for MP tray using Configuration Tool. For more information, refer to Configuration Tool on page 3-14. 2-16 Loading Paper 3 Connecting and Printing This chapter explains how to start up the printer, print from your PC, and use the application software included in the CD-ROM. Connections Installing the Printer Driver Printing Status Monitor Configuration Tool Uninstalling Software 3-2 3-3 3-7 3-10 3-14 3-18 Connecting and Printing 3-1 Connections This section explains how to start up the printer. Connecting the USB Cable Follow the steps as below for connecting the USB cable. 1 Connect the USB cable (not included) to the USB Interface Connector. Note Use a USB cable with a rectangular Type A plug and a square Type B plug. [. . . ] 2-9 Registration roller cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Removing memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Replacement toner container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2, 4-3 Replacing toner container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]