User manual KYOCERA FS-1500

[. . . ] The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No responsibility is assumed for defects in the printer's firmware (contents of its read-only memory). This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer, are protected by copyright. [. . . ] The printer's memory is running low because of the number of downloaded fonts and macros. Print a status page to see how much user memory is left and try deleting unnecessary fonts and macros. The waste toner reservoir is almost full. The waste toner reservoir will become full and the printer will stop printing. Contact your Kyocera Mita dealer. (No indication patterns available) Warning image adapt (No indication patterns available) Warning low memory Warning waste toner box Table 3-3 (Continued) 3-8 Indicators 3. 3. 2 Errors Requiring Service Personnel Attention When the following errors occur, turn off your printer, remove the plug from the AC outlet, and contact your Kyocera Mita dealer. The indicators are shown in two different states, according to the way they alternate. Indicator Corrective Action Main motor error (2000error) Contact your Kyocera Mita dealer. Scanner motor error (4000 error) Contact your Kyocera Mita dealer. Scanner pin-photo error (4200 error) Contact your Kyocera Mita dealer. Eraser error (5300 error) Contact your Kyocera Mita dealer. Table 3-4 3-9 Indicators Indicator Corrective Action Fuser error (6000 error) Contact your Kyocera Mita dealer. The waste toner reservoir is full (7980 error) Turn off the printer's power and remove the process unit from the printer. Gently shake the process unit horizontally a few times, then reinstall it into the printer. If this error message does not disappear, contact your Kyocera Mita dealer (less than 100, 000 pages printing). The waste toner reservoir is full (7990 error) Same as above (100, 000 pages printing or more). Controller check sum error (F010 error) Contact your Kyocera Mita dealer. Controller RAM read/write error (F020 error) Contact your Kyocera Mita dealer. Table 3-4 (Continued) 3-10 Indicators Indicator Corrective Action Controller system error (F030 error) Contact your Kyocera Mita dealer. Communication error (F040 error) Contact your Kyocera Mita dealer. Engine ROM check sum error (F050 error) Contact your Kyocera Mita dealer. Table 3-4 (Continued) 3-11 Indicators 3. 3. 3 Error Messages With the following errors, printing continues when you press the printer's key. You can confirm these errors by printing a status page. (See pages 1-4 and 1-5. ) Indicator KM-NET for Clients display File not found Press GO Corrective Action The specified file is not found. You can abandon printing by pressing the key. The printer is waiting for the end-of-job command before printing the last page. Pressing the key allows you to obtain the last page immediately. The printer is printing the last page after a waiting period. The printer is ready to print. Form Feed Timeout Ready The printer is offline. The printer stores but does not print received data. The indicator flashes at 5-second intervals and all other indicators go off. The printer wakes from Sleep mode whenever a key on the operator panel is pressed, the cover is opened or closed, or data is received. The printer then warms up and goes online. (You can set the amount of time before the printer enters sleep mode from the KM-NET for Clients utility. ) Table 3-6 3-14 Paper Jam Removal 3. 4 Paper Jam Removal This section describes how to remove paper when it jams in the printer. The printer will stop whenever paper jams in the printer or paper is not fed from a paper cassette. The printer will go offline and (paper jam) indicator will light in the operator panel. [. . . ] The KM-NET for Clients is contained on the Kyocera Mita Software Library CD-ROM supplied with the printer. Emulation This refers to emulation of manufacturers' printers. The printer emulates operation of the following printers: PCL, Line printer, IBM Proprinter, DIABLO 630, EPSON LQ-850, KPDL. KM-NET VIEWER This is a network management tool that can be used with the printer. You can view information for printers connected to the network using SNMP commands. KM-NET VIEWER is contained on the Kyocera Mita Software Library CD-ROM supplied with the printer. Expansion memory This option is used to increase printer memory. [. . . ]