User manual KYOCERA FS-1500A

[. . . ] The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No responsibility is assumed for defects in the printer's firmware (contents of its read-only memory). This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer, are protected by copyright. [. . . ] Each parameter is represented by two letters, such as R4 for default paper source, succeeded by FRPO, then followed by a value. For example, FRPO R4, 1; means that the default paper source (R4) is the printer's cassette (1). To confirm the current value for an FRPO parameter: 1 2 1 2 3 Enter the parameter (for example R4) in FRPO. The current value is shown in Value. To change the value for an FRPO parameter: Follow the above procedure to display the current value in Value. Erase the current value and enter the new value. For example, to change the default paper source to the MP Tray in the above example, enter 0 instead of 1 in Value. The value is changed. 1-50 Chapter 2 Printer Driver 2 This chapter describes how to perform basic print operations using the printer driver, such as setting the paper size and selecting a paper source. About the printer driver The Kyocera Mita Digital Library CD-ROM supplied with this printer contains the printer drivers for Windows and Macintosh computers. By installing this printer driver on your computer, you can print from Windows and Macintosh applications. This chapter explains the following topics: · · Installing the Printer Driver for Windows 95/98 Printing From Applications 2-1 Installing the Printer Driver for Windows 95/98 2. 1 Installing the Printer Driver for Windows 95/98 When you insert the Kyocera Mita Digital Library CD-ROM supplied with the printer into your computer, the setup screen is automatically displayed. To install the printer driver, follow the on-screen instructions. 2. 1. 1 Installing the Printer Driver Insert the Kyocera Mita Digital Library CD-ROM supplied with the printer into the CD-ROM drive of the computer. The Print dialog box is displayed again. Click the OK button to start printing. 2-7 Chapter 3 Maintenance 3 This chapter explains how to replace the toner container and how to clean parts such as the registration roller and charger wire. This chapter explains the following topics: · · Toner Container Replacement Cleaning 3-1 Toner Container Replacement 3. 1 Toner Container Replacement When the printer runs low on toner, the (toner) indicator flashes on the operator panel. Be sure to promptly replace the toner container and clean the inside of the printer when this message appears. If the printer stops printing while the toner container to continue printing. (toner) indicator is lit, replace the 3. 1. 1 Toner Container Replacement Interval Assuming an average toner coverage of 5%, with Ecoprint mode turned off the toner container will need replacing approximately once every 6, 000* printed copies. * In the case of a new printer in which a toner kit has been installed for the first time, the number of copies that can be printed will be approximately 3, 000. Toner Kit to be Used Name: TK-17 Description: Toner container Wiper cloth Plastic bag User's manual (The kit supplied with the printer only contains the toner container and wiper cloth. ) · Note Be sure to distance items such as floppy disks during toner container replacement. Be sure to clean the inside of the printer when replacing the toner container. Use of original Kyocera Mita toner kits is highly recommended to prevent printer trouble and ensure the long life of the printer. · · 3-2 Toner Container Replacement 3. 1. 2 Replenishing Toner 1 Open the printer's top cover. Top Cover 2 Pull lock lever #1 to the release (UNLOCK) position, then pull lock lever #2 to the release (right) position. Lock Lever #2 Lock Lever #1 3 Gently remove the old toner container. Put it in the supplied plastic bag and dispose of it. Plastic Bag 3-3 Toner Container Replacement 4 Take the toner container from the bag. [. . . ] The default setting is Off. Expansion memory This option is used to increase printer memory. The FS-1500A+ has one expansion slot, and you can install a 16 MB, 32 MB, 64 MB, or 128 MB DIMM (Dual Inline Memory Module). See your Kyocera dealer to purchase the DIMM that is best suited for use with this printer. KPDL2 (Kyocera Printer Description Language 2) This is Kyocera Mita's version of Adobe PostScript 2. To use this, the KPDL2 Upgrade Kit (PK-6) must be installed on your printer. Kyocera Mita Digital Library This is contained on the CD-ROM supplied with the printer. [. . . ]