User manual KYOCERA FS-1800

[. . . ] Table of Contents FS-1800 Page Printer Operation Guide Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The printer is factory-set to emulate the PCL. The emulation mode can be changed by following the procedures described in Chapter 1. Notice The information in this guide is subject to change without notification. Additional pages may be inserted in future editions. [. . . ] The audio alarm is set to On when leaving the factory. If the alarm is set to Off, it is made not to sound. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until Buzzer appears. >Buzzer On 5 ENTER Press the ENTER key. A blinking question mark (?) appears. >Buzzer ?On 6 Select On or Off using the or key. 7 ENTER Press the ENTER key. 8 MENU Press the MENU key. The message display returns to Ready. 1-130 Using the Operator Panel >Auto Continue > Mode Auto Continue Setting If an error that still allows you to continue printing occurs (Memory overflow Press GO, Print overrun Press GO, KPDL error Press GO, and File not found Press GO), the next received data is automatically printed after a set period of time elapses. For example, if the printer is shared over a network as a network printer and one person causes one of the above errors, after the set period of time elapses, the data sent from the next person is printed. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until Auto Continue > appears. >Auto Continue > Mode On 5 ENTER Press the ENTER key. A blinking question mark (?) appears. >Auto Continue Mode ?On 6 Select On or Off using the or key. 7 ENTER Press the ENTER key. 8 MENU Press the MENU key. The message display returns to Ready. 1-131 Using the Operator Panel Setting the Auto Continue Recovery Time Follow the procedure given below to change the recovery time for Auto Continue. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the appears. or key repeatedly until Auto Continue Mode > >Auto Continue > Mode On 5 6 ENTER Press the > key and display >>Auto Continue Timer. A blinking cursor ( ) appears. >>Auto Continue Timer 000Sec. 1-132 Using the Operator Panel 7 Press the or key to increase or decrease the value of the figure where the cursor is blinking and set the desired time. The time must be set between 000 and 495 seconds, in 5-second increments. If set to 000, printing will be continued immediately without allowing any time interval. You can use the > and < keys to move the cursor right and left. If you want to abandon the setting procedure, press the CANCEL key. 8 ENTER Display the desired time and press the ENTER key. 9 MENU Press the MENU key. The message display returns to Ready. 1-133 Using the Operator Panel >Service > Service Menu The service menu contains maintenance operations to be performed by service personnel. The Print Status Page, Toner ID, Developer, and Drum menus appear; however, in general, you will only need to use the Print Status Page and Toner ID menus. Printing the Service Status Page The service status page contains printer settings information that is more detailed than the standard status page and is therefore for mostly service purposes. However, since there is a great deal of information available on the service status page that may be helpful to you, the procedure for printing it out is given below. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until >Service > appears. >Service > 5 ? Press the > key. 6 Press the appears. or key repeatedly until >>Print Status Page >>Print Status Page 1-134 Using the Operator Panel 7 ENTER Press the ENTER key. A question mark (?) appears. >>Print Status Page ? 8 ENTER Press the ENTER key. The message display indicates Processing and printing starts. The message display returns to Ready. 9 MENU 1-135 Using the Operator Panel >>Toner ID Setting the Toner ID If the type of the toner kit (TK-60 [20, 000 pages] or TK-60E [10, 000 pages]) was changed, set the toner ID as follows so that on accurate toner gauge measurement is indicated on the status page. Also refer to the User's Manual supplied with the toner kit when replacing the toner container. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until >Service > appears. >Service > 5 ? Press the > key. 6 Press the or key repeatedly until >>Toner ID appears. >>Toner ID ## 1-136 Using the Operator Panel 7 ENTER Press the ENTER key. 8 Press the or key and display CA for the TK-60 or BA for the TK60E in place of ##. [. . . ] The Print dialog box is displayed again. The print job will be stored to the Microdrive without printing. To print, use the Print VMB Data menu in the e-MPS menu at the printer operator panel and specify the virtual mail box numbers. You can also print the list of virtual mail box trays. [. . . ]