User manual KYOCERA FS-4300DN

[. . . ] OPERATION GUIDE FS-2100D/FS-2100DN FS-4100DN/FS-4200DN/FS-4300DN This Operation Guide is for models FS-2100D, FS-2100DN, FS-4100DN, FS-4200DN and FS-4300DN. This Operation Guide is intended to help you operate the machine correctly, perform routine maintenance and take a simple troubleshooting action as necessary, so that you can always use the machine in good condition. We recommend the use of our own brand supplies. We will not be liable for any damage caused by the use of third party supplies in this machine. [. . . ] screen appears showing the available brightness settings. The list shows the following brightness settings: Darker -2 Darker -1 Normal 0 Lighter +1 Lighter +2 3 4 Press  or  to select the desired brightness. The brightness is set and the Device Common menu reappears. Disp. Backlight (Display backlight setting) Set the backlight for the message display. 1 Disp. Backlight: a b 1 *On ********************2 Off 3 Touched In the Device Common menu, press  or  to select Disp. The list shows the following display backlight settings: On (Standard) Off (No backlight)] Touched (Backlight lights up when the key on the operation panel is pressed) 2 Note If Touched is selected, the backlight turns off again when the panel is reset after the setting time of Auto Panel Reset has passed or when [Logout] is pressed. 3 4 Press  or  to select the desired backlight setting. The backlight setting is set and the Device Common menu reappears. Error Handling (Error detection setting) This specifies the settings for the detection methods used for duplex printing errors and for paper size and paper type errors when the paper source is fixed. The options available in Error Handling are as follows: • DuplexPaperError (Duplex printing error detection setting). . . 4-85 • Paper Mismatch (Detection settings for paper size/type errors when the paper source is fixed). . . 4-85 • MP Tray Empty (Warning when the MP tray is empty). . . 4-85 1 Error Handling: a b 1 DuplexPaperError ********************2 Paper Mismatch 3 MP Tray Empty [ Exit ] In the Device Common menu, press  or  to select Error Handling. The Error Handling menu screen appears. 2 4-84 Operation Panel DuplexPaperError (Duplex printing error detection setting) If the error detection setting for duplex printing has been turned Display Error, and you attempt to print onto a paper size and paper type that cannot be used for duplex printing, the Duplex disabled error message will be displayed and printing will stop. Display Error 1-sided • To print onto one-side of the paper only when this message is displayed, press [OK]. • Press [Cancel] to cancel the printing itself. • To print onto one-side of the paper. 1 DuplexPaperError: a b 1 *1-sided ********************2 Display Error In the Error Handling menu, press  or  to select DuplexPaperError. The DuplexPaperError screen appears. 2 3 4 Press  or  to select the setting for handling duplex paper errors. The handling of duplex paper errors is set and the Error Handling menu screen reappears. Paper Mismatch (Detection settings for paper size/type errors when the paper source is fixed) Select Continue in this setting if you want to continue printing even if the paper size or type you specified is different from the fixed paper source, or select Display Error to have the paper feed error displayed. 1 Paper Mismatch: a b 1 *Continue ********************2 Display Error In the Error Handling menu, press  or  to select Paper Mismatch. The Paper Mismatch screen appears. 2 3 4 Press  or  to select the setting for handling paper mismatch errors. The handling of paper mismatch errors is set and the Error Handling menu screen reappears. MP Tray Empty (Warning when the MP tray is empty) Turn this setting to On if you want the error displayed when the MP tray is configured as the default paper source, and there is no paper in the MP tray, or turn it to Off not to have the error displayed. The setting On enables the paper-empty message to display when the MP tray is empty. 1 In the Error Handling menu, press  or  to select MP Tray Empty. 4-85 Operation Panel MP Tray Empty: a b 1 Off 2 *On ********************- 2 Press [OK]. The MP Tray Empty screen appears. 3 4 Press  or  to select the setting for the paper-empty message to display. The display of MP Tray Empty is set and the Error Handling menu screen reappears. Timer Setting This specifies timer-related settings such as the automatic form-feed timeout and the timeout settings for Auto Sleep. IMPORTANT To change the Timer Setting, the administrator's Login User Name and Login Password must be entered. For details of the administrator settings, refer to Administrator on page 4-117. The options available in Timer Setting are as follows: • Auto Panel Reset (Auto panel reset setting). . . 4-87 • PanelReset Timer (Setting the panel reset timer). . . 4-88 • Sleep Level Set. (Sleep level setting). . . 4-88 • Sleep Timer (Sleep timer timeout time). . . 4-90 • Power Off Rule (Power Off Rule setting). . . 4-90 • Power Off Timer (Power off timer settings). . . 4-91 • Auto Err. Clear (Auto error clear setting). . . 4-91 • Err. [. . . ] In this way, "133. 210. 2. 0/24" denotes the IP address "133. 210. 2. 0" with a 24-bit prefix (network section). This new network address section (originally part of the host address) made possible by the subnet mask is referred to as the subnet address. When you enter the subnet mask, be sure to set the DHCP setting to Off. Glossary-3 Glossary TCP/IP (Transmission Control Protocol/Internet Protocol) TCP/IP is a suite of protocols designed to define the way computers and other devices communicate with each other over a network. TCP/IP (IPv6) TCP/IP (IPv6) is based on the current Internet protocol, TCP/IP (IPv4). IPv6 is the next-generation Internet protocol and expands the available address space, which resolves the problem of the lack of addresses under IPv4, while also introducing other improvements such as additional security functionality and the capacity to prioritize data transmission. USB (Universal Serial Bus) An interface standard for low to middle speed serial interfaces. [. . . ]