User manual KYOCERA FS-6020

[. . . ] FS-6020 Page Printer Operation Guide Please read the Operation Guide before using the printer. Keep it close to the printer for easy reference. The sections of this guide and parts of the printer marked with symbols are safety warnings meant to protect the user, other individuals and surrounding objects, and ensure correct and safe usage of the printer. The symbols and their meanings are indicated below. [. . . ] Parallel (default) USB Serial (when a serial interface board kit is installed) Option (when a network interface card is installed) 3 Press the ENTER key. A blinking question mark (?) appears. 3 Press the ENTER key. A blinking question mark (?) appears. Interface ?Parallel If you want to abandon the interface selection procedure, press the CANCEL key. The interface remains unchanged. Interface ?Parallel > If Parallel is not displayed, press the repeatedly until Parallel appears. or key 4 Press the pears. or key repeatedly until Serial ap- 4 5 6 Press the ENTER key again. Interface ?The message display changes to the communication mode menu. A blinking question mark (?) appears. 5 6 Press the ENTER key again. >Parallel I/F ?Each time the or key is pressed, the setting item and current setting change as shown on the next page. 1-43 Chapter 1 Using the Operator Panel Definable baud rates: 1200, 2400, 4800, 9600 (default), 19200, 38400, 57600, Definable data bits: 7, 8 (default) Definable stop bits: 1 (default), 2 Definable parity: None (default), Odd, Even, Ignore Definable protocol: DTR(pos. )&XON (default), DTP(positive), DTR (negative), XON/XOFF, ETX/ACK Changing Option Network Interface Parameters To make your printer support TCP/IP, Netware, and EtherTalk networks, you will need to install the option network interface card in the option interface slot of the printer and make the proper settings as explained in this section. Using the operator panel, you can: · · · Activate or deactivate TCP/IP, NetWare, and EtherTalk Activate or deactivate DHCP Enter IP address, subnet mask address, and default gateway address >Baud Rate 9600 >Data Bits 8 >Stop Bits 1 >Parity None To confirm or change network card parameters, proceed as follows: >Protocol DTR(pos. )&XON 1 2 Press the MENU key. Press the or key repeatedly until Interface > appears. One of the interface names shown below appears, indicating the current interface. Parallel (default) USB Serial (when a serial interface board kit is installed) Option (when a network interface card is installed) 7 Display the setting item to be changed and press the ENTER key. The following example explains how to change the baud rate. The settings for other items can be changed in a similar manner. 3 >Baud Rate ?9600 Press the or key to display the desired setting. The baud rate can be selected from 1200, 2400, 4800, 9600 (default), 19200, 38400, 57600, and 115200. NOTE Some computers may not be compatible with a baud rate of 115200 bps. If you set the baud rate to 115200 and communication problems occur, lower the baud rate. Press the ENTER key. A blinking question mark (?) appears. Interface ?Parallel 8 4 Press the pears. or key repeatedly until Option ap- Interface ?Option 5 Press the ENTER key again. 9 10 Display the desired baud rate and press the ENTER key. The message display returns to Ready. 1-44 Chapter 1 Using the Operator Panel 6 Press the key. [. . . ] 1 MB is equivalent to 1024 kB, or 1, 048, 576 bytes. MP tray This is an abbreviation for Multi-Purpose tray. The MP tray is used instead of the cassette when printing on envelopes, postcards, transparency sheets, and labels. Offline The printer can receive data, but cannot print. [. . . ]