User manual KYOCERA FS-7000+

[. . . ] Table of Contents Users Manual Kyocera Laser Printer FS-7000 The FS-7000+ in this photograph is equipped with two optional paper feeders and an optional document finisher. Introduction Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software _____________________________________________________________________________________ SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S NATIVE MODE OR ONE OF ITS EMULATION MODES. The printer is factory set to emulate the HP LJ 5M/5Si. The emulation mode can be changed by following the procedures described in Chapter 2. Notice ________________________________________________________________________________________________ The information in this manual is subject to change without notification. Additional pages may be inserted in future editions. [. . . ] This display only appears if the memory card contains data. will flash and a data name will appear after it. will flash, and a data name will appear. 4. You can scroll through data names on the memory card one by one by pressing the + key. Press the CANCEL key to cancel this operation. Press ENTER key while the data name you wish to delete is shown. The message display will change to Processing, and the printer will automatically print a partition list. Use this to check that the specified partition has been deleted properly. After the partition list is printed, the message display will return to Ready. Formatting Memory Card It is necessary to first format a new memory card before it can be used by the printer. A formatted memory card can then be written with data. Note _____________________________________________________________________ · · Note that if you format a memory card which already has data written on it, that data will be lost entirely. Check that the memory card can be written (that write-protection is released). 2-47 Memory Card 1. 3. Bring up the menu >Format on the message display. Pressing the ENTER key again will cause Processing to appear in the message display and the memory card will be formatted. The printer will print memory card formatting information (example below) after initialization is finished. Use this to check that the memory card has been formatted properly. Slot number: Slot name for the memory card (only A is supported) Card size: The overall memory capacity of the card (in units of bytes) Data size: The amount of data available to the system Remaining Size: The remaining amount of available memory on the memory card After this information is printed, the message display will return to Ready. 2-48 Chapter 2 Operating the Page Printer Printing a List of Data Names (Partitions) This operation prints the contents (data names, data size, etc. ) of the memory card inserted in the memory card slot. 1. 2. Bring up the menu >List of Partitions on the message display. Press the CANCEL key to cancel printing. 3. Pressing the ENTER key again will cause printing to start. After this information is printed, the message display will return to Ready. 2-49 Memory Card Note _____________________________________________________________________ "Remaining Size" in the partition list indicates the amount of remaining memory on the memory card. Since the system uses about 70 bytes to write a piece of data on the memory card, the actual available memory on the card is a little less than that displayed. 2-50 Chapter 2 Operating the Page Printer Setting the Paper Type This printer is capable of printing under the optimum setting for the type of paper being used. Setting the paper type for the paper source from the printer's control panel will cause the printer to automatically print in the mode best suited to that type of paper. This allows you to easily achieve high-quality printing results. A different paper type setting can be made for each paper source including the multipurpose tray. Not only can preset paper types be selected, but it is also possible for the user to define and select customized paper types. The following types of paper can be set. [. . . ] StatusPage >TCP/IP Off Off > >>NetWare Frame Auto > >>DHCP OFF >>IP Address >>Gateway >>Subnet Mask Continued on next page (Continued from previous page) >Code set ISO-6 ASCII Emulation HP LJ 5M/5Si > (*1) Emulation KC-GL > >KC-GL Pen width >KC-GL Page set > >>Pen (1) width 01 dot (s) 01 dot (s) Emulation KPDL > >Print KPDL errs Off On (*2) Emulation KPDL (AUTO) > >Alt. Emulation HPLJ 5M/5Si >Print KPDL errs Off On (*2) Emulation IBM Proprinter Line Printer Emulation DIABLO 630 Emulation EPSON LQ-850 Font Bitmap Scalable > >Code set IBM US > >Code set DIABLO US >Code set LQ US >Bitmap font 00001 >Courier Dark Light >AudreyTwo-Regu lar SWC >Courier Dark Light >Size 012. 00 point (s) >Pitch 10. 00 cpi > > > (*3) *1: *2: Depending on the emulation selected, the following set >code sets are available. The printer can be set to print error data during KPDL emulation. If this is set to On, error data will be printed if trouble occurs during printing. [. . . ]