User manual KYOCERA FS-9000

[. . . ] 7DEOHRI&RQWHQWV 8VHU·V0DQXDO . \RFHUD/DVHU3ULQWHU )6 7KH)6LQWKLVSKRWRJUDSKLVHTXLSSHGZLWKWZRRSWLRQDOSDSHUIHHGHUV3) DQGDQRSWLRQDOGRFXPHQWILQLVKHU') Introduction Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software _____________________________________________________________________________________ SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S NATIVE MODE OR ONE OF ITS EMULATION MODES. The printer is factory set to emulate the HP LJ 5M/5Si. The emulation mode can be changed by following the procedures described in Chapter 2. Notice ________________________________________________________________________________________________ The information in this manual is subject to change without notification. Additional pages may be inserted in future editions. [. . . ] The following types of paper can be set. For details on paper, please see Appendix B. Cassette, Media Type and Custom Settings Media Type Paper Type Plain Transparency Preprinted Labels Bond Recycled Vellum Rough Letterhead Color Prepunched Envelope Cardstock Custom #* MP tray \ \ \ \ \ \ \ \ \ \ \ \ \ \ Cassette \ 5 \ 5 \ \ 5 \ \ \ \ 5 5 \ EF (Envelope feeder) \ 5 \ \ \ \ 5 \ \ \ \ \ \ \ Duplex path (MP tray available only in Cassette mode) \ 5 \ 5 \ \ 5 \ \ \ \ 5 5 \ \: Can be stored 5: Cannot be stored *: This is a paper type defined and registered by the user. Up to eight types of user settings may be defined. A number from 1 to 8 is used in place of the #. For details on setting user types, please see page 2-52. 2-51 Setting the Paper Type Making Settings The following describes the procedure for setting the paper type using the Recycled type and Cassette 1 as examples. 1. Display Paper handling > on the printer's Mode Select Menu and press the 4 key. Then use the + and - keys to display the Cassette 1 type. Paper handling > >Cassette 1 type Plain 2. Press the + or - keys to display Recycled. >Cassette 1 type ?Recycled Press the CANCEL key if you want to cancel the setting. Pressing the EXIT key will exit the setting. The same procedure can be used to set the paper type for other paper sources. 2-52 Chapter 2 Operating the Page Printer Paper type user setting The following describes the procedure used to set a user-defined paper type for the printer. Eight custom user settings may be registered. After having been set, any of these may be called up when setting the paper type for a paper source. 1. Display Paper handling > on the printer's Mode Select Menu and press the 4 key. Then use the + and - keys to display >Custom setup. Paper handling > >Custom setup Custom # > 2. Press the + or - keys to select the paper type (see page 2-51) that you want to customize and then press the ENTER key. Custom # Note _____________________________________________________________________ Note that if you change the setting for a paper type other than Custom 1 through 8 the paper type setting for each paper source set to that paper type will be changed. 2-53 Setting the Paper Type 3. Press the 4 key after selecting the paper type you want to customize. Pressing the + or - keys will cycle through a display of the submenus given in the table below. Submenus displayed >>Paper weight Selection parameters Light(Thin) Normal (default) Heavy (Thick) Vellum Low Middle (default) High Enable (default) Disable Description Sets the paper thickness >>Fuser mode Sets the temperature for the fusing unit. >>Duplex path (only when the paper type is Custom #) Selects duplex printing on/off when a DU-31 is installed (setting active only for the selected paper type) Display the submenu to be set and press the ENTER key. [. . . ] Emulation HPLJ 5M/5Si >Print KPDL errs Off On (*2) Emulation IBM Proprinter Line Printer Emulation DIABLO 630 Emulation EPSON LQ-850 Font Bitmap Scalable > >Code set IBM US > >Code set DIABLO US >Code set LQ US >Bitmap font 00001 >Courier Dark Light >AudreyTwo-Regu lar SWC >Courier Dark Light >Size 012. 00 point (s) >Pitch 10. 00 cpi > > > (*3) *1: *2: Depending on the emulation selected, the following set >code sets are available. The printer can be set to print error data during KPDL emulation. If this is set to On, error data will be printed if trouble occurs during printing. This is set to Off before leaving the factory. [. . . ]