User manual KYOCERA FS-C5150DN

[. . . ] OPERATION GUIDE FS-C5150DN/FS-C5250DN FS-1100 FS-1300D Introduction Thank you for your purchase of FS-C5150DN/FS-C5250DN. This Operation Guide is intended to help you operate the machine correctly, perform routine maintenance and take a simple troubleshooting action as necessary, so that you can always use the machine in good condition. Please read this Operation Guide before you start using the machine, and keep it close to the machine for easy reference. We recommend the use of our own brand supplies. We will not be liable for any damage caused by the use of third party supplies in this machine. [. . . ] The display returns to Ready. IP Address (IP address setting) An IP address is the address of a network device such as a computer and is included in IP packets as needed for the sending and receiving of Internet data (IP packets). (IP addresses can be either destination addresses or source addresses. ) Specifically, an IP address is a bit string consisting of a host address (or host section) that identifies a computer (host) connected to the Internet and a network address (or network section) that identifies the network to which that computer belongs (or more specifically, the computer's 4-47 Using the Operation Panel network interface). Bit strings (IP addresses) that are unique throughout the entire Internet system are allocated to each computer or interface. The IP addresses currently used on the Internet (IPv4) have a fixed length of 32 bits. Note When you enter the IP address, be sure to set the DHCP setting to Off. 1 2 >>IP Address 000. 000. 000. 000 Press Press while >TCP/IP or On > is displayed. repeatedly until >>IP Address appears. 3 Press [OK]. A blinking cursor (_) appears. 4 5 6 Press or to increase or decrease, respectively, the value at the blinking cursor. You can set any value between 000 and 255. Use and to move the cursor right and left. Display the desired IP address and press [OK]. The display returns to Ready. Subnet Mask (Subnet mask setting) The subnet mask is a way of augmenting the network address section of an IP address. A subnet mask represents all network address sections as 1 and all host address sections as 0. The number of bits in the prefix indicates the length of the network address. The term "prefix" refers to something added to the beginning and, in this context, indicates the first section of the IP address. When an IP address is written, the length of the network address can indicated by the prefix length after a forward slash (/). For example, "24" in the address "133. 210. 2. 0/24". In this way, "133. 210. 2. 0/24" denotes the IP address "133. 210. 2. 0" with a 24-bit prefix (network section). This new network address section (originally part of the host address) made possible by the subnet mask is referred to as the subnet address. Note When you enter the subnet mask, be sure to set the DHCP setting to Off. 1 2 >>Subnet Mask 000. 000. 000. 000 Press Press while >TCP/IP or On > is displayed. repeatedly until >>Subnet Mask appears. 3 Press [OK]. A blinking cursor (_) appears. 4 5 6 Press or to increase or decrease, respectively, the value at the blinking cursor. You can set any value between 000 and 255. Use and to move the cursor right and left. Display the desired subnet mask and press [OK]. The display returns to Ready. 4-48 Using the Operation Panel Gateway (Gateway setting) Gateway generally refers to a protocol conversion device used to allow networks with differing protocol systems to interconnect. For example, a "Gateway" device is required to connect a different closed network (using its own protocols) to the open Internet (using TCP/IP). [. . . ] You can specify the font size in steps of 0. 25 points up to 999. 75 points. PostScript This is a page description language developed by Adobe Systems, Inc. It enables flexible font functions and highly-functional graphics, allowing higher quality printing. PPM (prints per minute) This indicates the number of printouts made in one minute. Printer driver The printer driver makes it possible for you to print data created using application software. The printer driver for the printer is contained on the CD-ROM supplied with the printer. Install the printer driver on the computer connected to the printer. Glossary-2 Glossary Sleep mode This mode is provided to save power. [. . . ]