User manual KYOCERA KM-1620

[. . . ] KM-1620 Please read the Operation Guide before using the copier. Keep it close to the copier for easy reference. In areas of the GEEA, the available setting for the Off Mode to engage is between 1 and 120 minutes, and the available setting for the Low Power Mode to engage is any 1 minute, 5 minutes, 15 minutes, 30 minutes, 45 minutes, 60 minutes, 90 minutes or 120 minutes. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Legal Restriction On Copying · It may be prohibited to copy copyrighted material without permission of the copyright owner. [. . . ] Sets the copier so that each copy set is rotated and sorted when it is sort-copied. Shortens the amount of time the internal motor continues to run after the copy is produced. Use this setting in cases when the motor noise is bothersome. Sets the copier so that automatic clearing is executed after a set amount of time has elapsed after the copy is produced. (Refer to P. 2-4 "Regarding the Auto-clear function". ) Available settings 1-: No Borderline* 2-: Solid Line 3-: Dotted Line on: Rotational Sorting Enabled oFF: Rotational Sorting Disabled* 0, 5, 10, 15, 30 (seconds) (*10) Reference Page 6-27 F30 6-28 F31 Silent Mode Transition Time Auto Clear Setting 6-28 F32 on: Enabled* oFF: Disabled 6-29 F33 Auto Off Setting The Auto Off mode will be entered after a set period of on: Enabled* time has passed after the final copy has been produced oFF: Disabled or during which no operations have been performed. If the Auto Off function interferes with your copy operations, disable the function. Before disabling the Auto Off function, you may want to try lengthening the amount of time before the Auto Off function engages (Off Mode Transition Time). Sets the time interval prior to the automatic operation of the Auto Clear function when on (Enable) has been selected as the Auto Clear setting. * This will not be displayed when F32 is set to "oFF". Sets the time interval prior to the automatic engagement of the Low Power mode after copy operations have been completed. Sets the time interval prior to the automatic operation of the Auto Clear function when on (Enable) has been selected as the Auto Clear setting. * This will not be displayed when F33 is set to "oFF". The Alarm can be set to sound when a key on the Operation Panel is pressed or in cases when errors occur, etc. 10 - 270 (10-second units) (*90) 6-29 F34 Auto Clear Time 6-30 F35 Low Power Mode Transition Time Off Mode Transition Time 1, 5, 15, 30, 45, 60, 90, 120, 180, 240 (minutes) (*15) 1, 5, 15, 30, 45, 60, 90, 120, 180, 240 (minutes) (*30) 6-31 F36 6-31 F37 Alarm on: Enabled (sound alarm) oFF: Disabled (no alarm)* 6-32 F38 Toner Coverage Report Prints out a report that shows the number of copies --made and the average amount of toner used (blackness ratio %) for each paper size. 6-33 6-10 Section 6 COPIER MANAGEMENT Default Settings Mode Operations Procedures Follow the procedure listed below to operate in the [Default Settings Mode]. 4 Press the [OK] key. Inch specifications Metric specifications 1 Depress the [Exposure Adjustment] keys on both sides for 3 seconds. "F00 (Default Settings Mode)" will be displayed in the No. of Copies display. Procedure for Changing the Default Settings The procedure for changing each of the items in the Default Settings is described below. Press either the Zoom (+) key or the Zoom (­) key and select each Default Settings Mode. Inch specifications Metric specifications 2 User Status Report Outputs a list of the values set for the Default Settings items. Note Check to make sure that 11" × 8 1/2"/A4 size paper is loaded in the drawer. 1 Display the Default Settings Mode. (Refer to P. 6-11 "Default Settings Mode Operations Procedures". ) Inch specifications Metric specifications Notes · Each of the Default Setting Modes can be selected by pressing the Keypad keys. · Refer to "Procedure for Changing the Default Settings" regarding the following. 3 After completing each operation, press on the Zoom (+) or Zoom (­) key to display "F00". Inch specifications Metric specifications 2 Press either the Zoom (+) or Zoom (­) key to display "F01". [. . . ] 6-25 Merge Copy Borderline (Default Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27 Mixed Original Sizes (Auto Selection) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Multi-bypass tray Paper Size (Default Settings) . . . . . . . . . . . . . . . . . . . . . . . 6-22 Multi-bypass tray Size Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]