User manual KYOCERA KM-C830D

[. . . ] Operation Guide * The illustration above shows the copier with the optional original cover installed. Please read the Operation Guide before using the copier. Keep it close to the copier for easy reference. <IMPORTANT> This Operation Guide is for the KM-C830 and KM-C830D copiers. The instructions contained herein are based on the KM-C830 standard copier (for 1-sided copies only) and KM-C830D duplex copier (for 2-sided copies). · Standard equipment KM-C830: Two 500-sheet capacity drawers KM-C830D: Duplex Unit and one 500-sheet capacity drawer NOTE: This Operation Guide contains information that corresponds to using both the inch and metric versions of this copier. [. . . ] Inch specifications NOTES · Each transparency and backing sheet will be ejected first, followed by the set of standard copies. · If the optional Document Finisher is installed in your copier, the transparencies and backing sheets will be ejected onto the non-sort tray on the Document Finisher and the standard copy sets will be ejected one by one onto its sort tray. Metric specifications 6-24 Section 6 FUNCTIONS 13 Press the Start key. · If you set the originals in the optional DF, copying will start automatically. · If you set the original on the platen, go to the next step. Inch specifications Metric specifications 14 Replace the first original with the next one and press the Start key. Scanning of that next original will start. Carry out this step for all of the originals that you want to copy and, once you have finished scanning them all, press the Enter key. Inch specifications Metric specifications 6-25 Section 6 FUNCTIONS 12. Adding covers and separation inserts to your copy sets [Insert sheet modes] There are two insert sheet modes: cover and separation insert. (1) Insert sheet modes G Cover mode With this mode, paper fed from the multi-bypass tray is added as front and back covers to the copy sets. The front cover can be made into a 1-sided copy or be left blank. With the back cover, you can select whether to copy onto the cover or not, as well as whether or not to even including a back cover at all. NOTE If you do not have a Memory Copy Board installed as standard equipment, the optional Memory Copy Board must be installed in your copier in order to use this mode. * Refer to the following table for the types of finished copies that each combination of settings will make. Back cover Original Front cover Copy on front Blank No back cover Copy on front Blank * The illustration shows the result when 1-sided copies are made. 6-26 Section 6 FUNCTIONS G Separation insert mode With this mode, sheets can be inserted at specified points among copies of multiple originals. You can also select whether to copy onto the inserted sheets themselves or not. 1 If you choose to copy on the front and back side of the insert sheets. . . * The illustration shows the result when 2-sided copies are made. 2 If you choose to copy on the front side of the insert sheets only. . . * The illustration shows the result when 2-sided copies are made. NOTES · The drawer which contains the paper that to be fed as insert sheets must be designated in advance. (See "* Insert tray" on page 7-21. ) · If "Bypass" is selected under "* Insert tray" on page 7-21, it will not be possible to make 2-sided copies of the separation inserts. · The available settings for this mode will differ depending upon the type of originals being copied and the type of finished copies that are being made. A circle (" ") in the following table indicates that the setting is possible. 3 If you choose to leave both the front and back side of the insert sheets blank. . . * The illustration shows the result when 2-sided copies are made. Types of copy settings available Original/ Copy type 1-sided originals 1-sided copies 2-sided copies 2-sided originals 1-sided copies 2-sided copies Copy onto front and back Copy on front only Leave both front and back blank 6-27 Section 6 FUNCTIONS (2) Making copies with the insert sheet modes 5 6 Press the Enter key. · If your machine is a duplex copier, go to the next step · If your machine is a standard copier, go directly to step 10. Use the M cursor or the N cursor key to select the type of finished copies you want to make. [. . . ] Safety of laser beam This copier has been certified by the manufacturer to Class 1 level under the radiation performance standards established by the U. S. DHHS (Department of Health and Human Services) in 1968. This indicates that the product is safe to use during normal operation and maintenance. The laser optical system, enclosed in a protective housing and sealed within the external covers, never permits the laser beam to escape. 2. [. . . ]