User manual KYOCERA KM-P4845W

[. . . ] Wide Format Printer Operation Guide Please read the Operation Guide before using the printer. Keep it in the designated location for easy reference. As an ENERGY STAR Partner, KYOCERA MITA AMERICA, INC. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. registered mark. NOTE · This Operation Guide applies to models KM-P4845w and KM-P4850w. [. . . ] After setting the paper roll, check that the flange tray has not moved. 4 Insert an included flange into the core of the new roll. 2 2 3-7 CHAPTER 3 GETTING READY FOR PRINTING 8 Grasp both paper roll insertion latches 3 and open the paper roll insertion cover 4. IMPORTANT If the paper roll that has been set is slackened, grasp the flange and wind the paper roll to remove the slack. If not, the paper may be fed obliquely. 3 4 3 9 Insert the leading edge of the paper under the paper roll insertion guide and advance the edge past the guide approximately 1/2" [10 mm] as shown in the illustration. 11 1/2" [10mm] Insert the roll unit securely into the main body of the machine. To align the leading edge of the paper roll, use the N or M key to select a paper tray and press the Roll Cut key. The leading edge of the paper roll will be ejected from the paper eject slot. 12 13 NOTE If the leading edge of the paper roll is folded or broken, cut a clean edge using a cutter. NOTE · Paper is normally cut in lengths of 11" [279 mm]. If the temperature in the machine is lower than 15 °C, however, vellum will be cut in lengths of 31" [800 mm]. · When a paper roll has been replaced during printing, press the On Line key to place the printer offline and then press the Roll Cut key. To continue printing press the On Line key once more to place the printer online. 10 Grasp the paper roll insertion latches and close the paper roll insertion cover securely. 3-8 CHAPTER 3 GETTING READY FOR PRINTING (3) Dew prevention heater If the humidity is high (more than 70 %RH) or drastic temperature change occurs, turn on ( l ) the dew prevention heater switch when using the machine. Even if the main switch is off ( ), the dew prevention heater switch can be on ( l ). (4) How to Use the Paper Tray Support Plate Set the paper tray support plate based on the paper to be used for printing. 1 Incline the paper tray support plate and slide it to the size indication on the size label of the paper tray. IMPORTANT When using vellum or film, be sure to turn off ( O ) the dew prevention heater switch. If not, paper may be wrinkled or curled. 2 After setting the paper tray support plate to the desired size, return it to a horizontal state. 3 Follow the same procedure to set the other paper tray support plate to the same height. Depending on the paper to be used and the environment, the support plate may not be contained at the position of the size label. In this case, adjust the position of the paper tray support plate upward or downward. 3-9 CHAPTER 3 GETTING READY FOR PRINTING 3-10 CHAPTER 4 PRINTER OPERATION 1. Basic printing Perform this procedure in order to send commands to the printer from your computer. 1 Turn the main switch on the printer ON ( | ). The printer will begin to warm up and "Ready to print. " will be displayed once warm-up is complete. CAUTION 2 Make sure that the Ready indicator is lit. If the printer will not be used for a short period of time (overnight, etc. ), turn the main switch OFF ( ). If it will not be used for an extended period of time (vacations, etc. ), remove the power plug from the outlet for safety purposes during the time the printer is not in use. 3 NOTE Perform the appropriate printing procedure on your computer. Refer to the Functions Edition (On-Line Manual) for more detailed information on printing from your computer. 4-1 CHAPTER 4 PRINTER OPERATION 2. Printing with manually fed media When printing through the bypass slot, perform the following procedure. 3 NOTE Perform the appropriate printing procedure on your computer. NOTE · Only one sheet of paper can be set onto the bypass table at a time. · When using curled paper, smooth the paper. If the curling persists, place the paper with the curled surface up. Refer to the Functions Edition (On-Line Manual) for more detailed information on printing from your computer. 1 Adjust the bypass guides to the paper size indications on both sides of the bypass table. 4 When the message "Set paper. bypass" appears, refer to Step 2 and set the next sheet onto the bypass table. Repeat this procedure to set sheets one at a time onto the bypass table until the required number of sheets has been loaded and printed. 2 Set the paper face down all the way into the feed slot aligned with the paper size indication. When placing paper in the bypass table, set the paper quickly all the way into the feed slot. Once the paper is fed, release the paper. If the paper is not set properly, a paper jam may be detected. [. . . ] Dry Toner supply system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bottle cartridge system Fixing system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heat roller Cleaning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blade and fur brush Photoconductor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]