User manual KYOSHO CALMATO 40 SPORTS EXPLODED VIEW

[. . . ] All Rights Reserved Document: MICROLINE CALMATO 40 SPORTS User's Guide Revised Edition: July, 2004 Written and produced by the Oki Data Training and Publications Department. Please address any comments on this publication to: Oki Data Americas, Inc. Training and Publications Department 2000 Bishops Gate Blvd. Mount Laurel, NJ 08054-4620 We invite you to visit Oki Data's multilingual web site at: http://www. okidata. com. KYOSHO, Oki Data and MICROLINE are registered trademarks of Oki Electric Industry Company, Ltd. [. . . ] To change the settings for the serial interface, use the two banks of switches on the serial interface board: 1. Use a Phillips bit screwdriver to remove the serial switch access cover (1) at the back of the printer: 3. Make any needed changes in the switch banks (SW1 and SW2), See the tables below. 4. Reinstall the access cover and turn the printer on. 36 · Setting Up Your Printer Serial Interface Parameters Note: Defaults are underlined. Switch Bank 1 Parity Type Odd Parity Even Parity Parity No parity With parity Data Bits 8 bits 7 bits Protocol ReadyBusy X-ON/X-OFF Test Select Circuit Monitor Mode Select Print mode Test mode Busy Line Selection SSD- Pin 11 SSD+ Pin 11 DTR- Pin 20 RTS- Pin 4 Switch 1 ON OFF Switch 2 ON OFF Switch 3 ON OFF Switch 4 ON OFF Switch 5 ON OFF Switch 6 ON OFF Switches 7, 8 OFF, ON OFF, OFF ON, ON ON, OFF Switch Bank 2 Transmission Speed 19, 299 bps 9, 600 bps 4, 800 bps 2, 400 bps 1, 200 bps 600bps 300 bpc 110 bps DSR Input Signal Active Inactive Buffer Threshold 32 bytes 256 bytes Busy Signal Timing 200 ms minimum 1 second minimum DTR Signal Space after power on Space when printer selected Not Used Switches 1, 2 ON, ON, ON OFF, ON, ON ON. OFF, ON OFF, OFF, ON ON, ON, OFF OFF, ON, OFF ON, OFF, OFF OFF, OFF, OFF Switch 4 ON OFF Switch 5 ON OFF Switch 6 ON OFF Switch 7 ON OFF Switch 8 37 · Setting Up Your Printer Setting up the Printer to Work with Your Computer Note · Settings made in your software application normally override settings made in your printer driver. · Settings made in the printer driver normally override settings made in the printer menu or via the front panel. Windows XP, 2000, Me, 98, 95, NT 4. 0: Install the Printer Driver To print from a Windows-based system, install the printer driver located in the Drivers folder on the CD supplied with your printer. This driver incorporates commands which use the full capability of the printer and automatically switches the printer to the correct emulation regardless of which emulation is selected in the printer menu. Click Start Settings Printers. 38 · Setting Up Your Printer 3. When you get to the window which asks you to select the manufacturer and model of your printer, click Have Disk, then browse to the appropriate directory on the CD and double click the inf file: Windows Version XP 2000 98 Me 95B [OSR2] NT 4. 0 . inf File Location \Drivers\WinXP\English\Oemprint. inf \Drivers\Win2k\English\Oemprint. inf \Drivers\Win98_Me\English\Oemsetup. inf \Drivers\Win98_Me\English\Oemsetup. inf \Drivers\Win95\English\Oemsetup. inf \Drivers\NT40\English\Printer. inf 6. Follow the on-screen instructions to finish loading the driver. Non-Windows Systems: Set the Emulation in the Printer Menu Your printer has three emulations: · IBM® 2480 -- the factory default · Epson® ESC/P2 · Oki Data® MICROLINE® Standard If you are using a non-Windows system such as LINUX®, a non-Windows application such as a DOS® program, or an older application such as Word Perfect® 5. 1, you need to make sure you have the correct emulation selected in the printer menu (see "Changing the Emulation Default in the Printer Menu" below). Prints list of current menu settings. Toggles the printer on and off line. Places printer in Menu Mode. Selects the character pitch setting (cpi). Sets print mode (NLQ, Utility, HSD). PITCH + MODE Not applicable. = save settings and exit to print mode. PITCH + MODE Not applicable. = save settings and exit to print mode. 44 · Operating Your Printer Setting Printer Defaults The printer has an internal menu containing a number of default parameters which can be set to enable your printer to match the parameters required by your computer. Using the Menu Mode Entering the Menu Mode To enter the Menu Mode, press SELECT while turning on the printer. The 12 and UTILITY LEDs flash. Printing a List of Current Menu Settings With the printer in the Menu Mode, press SELECT to print the complete menu. The current default settings print out. 45 · Operating Your Printer Sample Default Menu Printout Parallel/USB Model Printer Control Font Font Font Font Font Font Symbol Sets Symbol Sets Symbol Sets Symbol Sets Vertical Control Vertical Control Vertical Control Emulation Mode Print Mode DRAFT Mode Pitch Proportional Spacing Style Size Character Set Language Set Zero Character Code Page Line Spacing Skip Over Perforation Page Length IBM Utility SSD 10 CPI No Normal Single Set I American Slashed USA 6 LPI No 11 " Set-Up Graphics Uni-directional Set-Up Receive Buffer Size 64K Set-Up Paper Out Override No Set-Up Print Registration 0 ||||||||||||||||||||| <----- |||||| --------> ||||||||||||||||||| Set-Up Operator Panel Function Full Operation Set-Up Reset Inhibit No Set-Up Print Suppress Effective Yes Set-Up Auto LF No Set-Up Auto CR Yes Set-Up SI Select Pitch (10CPI) 17. 1 CPI Set-Up SI Select Pitch (12CPI) 12 CPI Set-Up Time Out Print Invalid Set-Up Auto Select No Set-Up ESC SI Pitch 17. 1 CPI Set-Up Impact Mode Normal Parallel I/F Parallel I/F Parallel I/F I-Prime Pin 18 Bi-direction Buffer Print +5v Enable 46 · Operating Your Printer Changing Menu Settings 1. Press SELECT while turning on the printer. Press LINE FEED to select the relevant group that needs to be changed (the group is the left-hand column on the Menu printout). Press FORM FEED to select the relevant item within the selected group (the Item is the center column on the Menu printout). Press TOF SET to cycle through the settings available for the item you want to change (the settings are the right-hand column on the Menu printout). To continue making changes: · press LINE FEED for the next group or · press FORM FEED for the next item. Repeat the previous step until you are finished changing settings. Press PITCH and MODE together to save the changes you have made and exit the Menu Mode. Important Exiting the Menu Mode by turning off the printer will cancel any changes you have made. 47 · Operating Your Printer For Example The default setting for the zero character is slashed. [. . . ] 5 72 · Index M Menu changing settings . . . . . . . . . . . . . . . 47­48 default settings . . . . . . . . . . . . . . . . . . . 51­52 defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 settings, changing . . . . . . . . . . . . . . . . . . . 47 Menu mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45­52 MODE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Mode lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 N Noise level specifications . . . . . . . . . . . 70 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 O Options pull tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 roll paper stand . . . . . . . . . . . . . . . . . . . . . . . . . 67 Power cord replacement # . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 POWER light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Print speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]