User manual KYOSHO DNX301 PARTS LIST

[. . . ] Written and produced by the Oki Data Training and Publications Department. Please address any comments on this publication to: Training & Publications Dept. Mount Laurel, New Jersey 08054-4620 KYOSHO, KYOSHODATA and MICROLINE are registered trademarks of Oki Electric Industry Company, Ltd. ENERGY STAR is a registered trademark of the United States Environmental Protection Agency. [. . . ] The printhead can get very hot during extended periods of printing--be sure to let it cool off before you touch it. à Leave the clear plastic ribbon shield (1) on the cartridge!Use only genuine Oki Data ribbon cartridges. 8 | Setting Up 3 If you are replacing the ribbon cartridge, grasp the sides of the cartridge at either side of the printhead (Caution!printhead can be HOT!), then lift the used cartridge out and discard it. 4 With the knob side up, tilt the new ribbon cartridge onto the printhead plate so that it slides into the area of the plate that is closest to the front of the printer, then lower the ribbon shield over the printhead (Caution!Printhead may be HOT!), aligning the tabs with the inserts on the printhead plate. If the ribbon won't load easily, turn the knob slightly until the x-shaped notch on the bottom of the ribbon cartridge aligns with the x-shaped insert on the ribbon plate. 5 Press on the cartridge until you feel it snap into place. 6 If you are replacing the ribbon cartridge, put the access cover back on and press down until it snaps into place, then replace the acoustic cover. Printer Handbook: English | 9 Install the Platen Knob Insert the knob in the hole on the right side of the printer, lining up the notch in the knob with the pin on the shaft. Install the Paper Separator Place the tabs (1) on the paper separator into the slots (2) on the printer, then press down to snap it in place. 10 | Setting Up Install the Power Cord 1 Make sure the printer is turned off. Connect To the Computer The interface cable is not supplied with the printer. 1 Insert the plug into the parallel port on the back of the printer (1) and secure it with the wire clips (2). 2 Plug the power cord supplied with your printer into the power socket (1). à The outlet voltage must match the voltage marked on the printer label. 2 If necessary, use the grounding screw suplied with the printer to attach the frame ground wire to the hole (3) at the right of the parallel port. 3 Connect the other end of the cable to the computer. 4 Turn the printer on. 3 Plug the opposite end into a grounded outlet. Printer Handbook: English | 11 Load Paper The maximum usable thickness of multi-part forms is 0. 014 inch (0. 36 mm). Paper Lever Positions = Continuous Forms Set the Printhead Gap Lever Before you load continuous paper, be sure to set the blue printhead gap lever (1) as follows: = Single Sheet Bail Lever Positions · position 1 for 1- or 2-part paper · position 2 for 3- or 4-part paper · position 3 for 5-part, extra-thick paper. Open Closed 12 | Setting Up Loading Continuous Form Paper for Bottom Feed 2 Place the paper stack on the bottom of the printer stand. If the printer is on and selected (SELECT light on), press the SELECT button to deselect it. If you are reloading paper, remove the acoustic cover and the access cover. 3 Pull the paper lever (1) forward (continuous forms position) and open the bail lever (2). 1 Set the printer on a slotted printer stand (optional, available from third party), aligning the opening in the base of the printer with the slot on the stand. Printer Handbook: English | 13 4 Slide the paper through the opening in the base of the printer, then push the paper lever (1) back (single sheet position) and turn the platen knob (2) to move the paper up level with the paper bail (3). 6 Pull up the lock levers (1) to release the tractors and open the tractor covers (2). The pins (1) at either end of the platen are not used with the pull tractor installed. Please leave them locked in place. 5 Pull the paper lever forward. 14 | Setting Up 7 Slide the tractors to align them with the edges of the paper, then set the paper holes on the tractor pins (1). 8 Click OK The DNX301 appears in the Installed Printers box. 9 Click Setup and select Tractor under Paper Source, then click OK. 10 To use a port other than LPT1:, click Connect and select another port, then click OK. 11 With KYOSHO DATA DNX301 selected in the Installed Printers box, click Set as Default Printer. 12 Click Close. 24 | Controlling the Printer Appendix A: Replacement Parts Item KYOSHO Number Ribbon Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52102001 Printhead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50063802 Platen Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40673402 Item KYOSHO Number Acoustic Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53450001 Pull Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50044701 Item KYOSHO Number Access Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42178701 Paper Separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 29 Printer dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Printhead gap lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]