User manual KYOSHO FORMULA D SILVIA S15 NO11 HANKOOK JIC 2007 PARTS LIST

[. . . ] Press to enter the Menu . . . Changing Defaults To change the printer's default settings for print media, see pages 6 and 7. MAINTENANCE MENU ENTER 3. Press . MENU RESET EXECUTE ENTER 4. Press . The printer resets and returns to the on-line state. 4 Media Settings (cont. ) Media Settings for Individual Print Jobs If you are printing a job on special media, you can temporarily load the media in a tray and change the media settings for that tray in the driver as you print the job. Table 1: Media Weight Settings, US Bond Setting US Bond (Metric) Light Medium Heavy Ranges for Printer Media Weight Settings Note: To determine if a paper weight Ultra Heavy 16 to 19 lb. (124 to 203 g/m2) is US Bond or Index, check the metric equivalent. [. . . ] Press . TRAY1 PAPERSIZE LETTER The setting is engaged and the second line of the display stops blinking. * 8. If you are setting the MP Tray for envelopes: ON LINE Press and you are done. If you are setting the MP Tray for heavy paper or labels, keep going. 8 Changing Default Media Setting MP Tray (cont. ) Then, Set the Media Type (Heavy Paper and Labels Only) 1. Press . The printer goes back on line. You're done! MPT MEDIATYPE PLAIN ENTER * 2. Press . The second line of the display starts blinking. Press . . . MPT MEDIATYPE YYYY YYYY = LABELS or CARD STOCK. ENTER BACK 4. Press , press . The setting is engaged and the second line of the display stops blinking. 9 Loading Media Trays 1 & 2 Media Weight Range Tray 1:16 to 32 lb. US Bond (60 to 120 g/m2) Tray 2:16 to 47 lb. US Bond (60 to 177 g/m2) Letter, Legal-14, Legal-13. 5, Legal-13, A4, A5, A6, B5, Executive, Custom (min. 3. 94'' x 5. 83'' [100 x 148 mm], max. 8. 5'' x 14'' [215. 9 x 355. 6 mm]) 300 sheets of 20-lb. Press . . . POW SAVE TIME XX MIN Setting the Power Save Interval Note: The ". . . " in these steps XX = 5, 15, 30, 60 (default), or 240 minutes. ENTER BACK 5. Press , press . indicates that you should keep pressing the button repeatedly until you see the display indicated. 6. SYSTEM CONFIG MENU The new setting is engaged and the second line of the display stops blinking. ON LINE . To Disable/Enable Power Save 1. Press POW SAVE TIME 60 MIN ENTER * MAINTENANCE MENU 3. Press . The second line of the display starts blinking. 20 Power Save Parameters (cont. ) 4. Press . POWER SAVE DISABLE Pressing the + button toggles back and forth between Enable and Disable. ENTER BACK 6. Press , press . The new setting is engaged and the second line of the display stops blinking. ON LINE 7. Press . 21 Control Panel Buttons READY BACK ENTER MENU ON LINE ATTENTION CANCEL Back Press this button to go back to the previous Item or Category, or to place the printer back on line. BACK On Line Press ON LINE to switch the printer between on line and off line status. ON LINE Menu + Press MENU + to enter the Menu mode or to go to the next Category in the Menu. When the printer is in the Menu mode, press ON LINE to exit the Menu mode and return the printer to its previous status (on or off line). If there is a paper size mismatch error, press ON LINE to force the job to print. Press ON LINE to start a manual print job from the MP Tray. If there is a memory overflow, press ON LINE to recover and place the printer back on line. Menu ­ Press MENU ­ to go back to the previous Category in the Menu or to exit the Menu mode. Enter Press ENTER to select the Item or Value. ENTER Cancel Press CANCEL to stop printing the current job. CANCEL 22 Control Panel Lights READY BACK ENTER MENU ON LINE ATTENTION CANCEL READY Ready LED (Green) On: printer is on line. [. . . ] Press down on the fuser to be sure it is firmly locked in place. The message should disappear. Note: If the message still appears, Press the ON LINE button. CANCELLING JOB (USER DENIED) push the blue latches at either end of the fuser back (toward the printer cover hinge) and lift the fuser out, then lower it back into the printer, pushing it firmly down in place. You should feel the latches at either end engage. Close the cover. The Job Accounting software has detected a print job from a user who is either · not authorized to print or · trying to print a color job and only authorized to print black and white job. . What to Do XXX TONER SENSOR ERROR The user should contact the system Administrator to see if their authorization can be changed. Appears on the second line of the display to indicate that there is a problem with the color xxx toner sensor. What to Do Turn the printer off, then on again. [. . . ]