User manual KYOSHO GP ULTIMA ST SPORTS PARTS LIST

[. . . ] Keep the packing materials and carton in case you ever need to ship or transport your printer. 2 Remove shipping restraints (1, 2) and protective film (3, 4). 4 Install any accessories you purchased. Refer to the instructions provided with each accessory. [. . . ] 5 Connect to the computer and the power outlet (computer and printer both OFF). 6 Turn the computer and printer on. 1 2 3 4 * Models GP ULTIMA ST SPORTS, ML521, ML590 and ML591 Loading Paper Your printer has three print paths: · Rear Feed for continuous forms (see below) · Top Feed for single sheets (see "Loading Single-Sheet Paper" under "Section 1: Getting Started" in the User's Guide) · Bottom Feed--requires optional pull/push tractors--for thick multi-part forms, coninuous-form labels, cards, etc. (see instructions provided with the optional tractor). 5 Place the wire guide (1) on the pull-up roller assembly (2). 1 SEL SEL MENU SHIFT Loading Rear Feed Paper 1 Move the paper lever (1) to the REAR position. 1 LF Micro Feed Down FF/LOAD Micro Feed Up TEAR PARK QUIET TOF EXIT POWER ALARM GROUP ITEM SET PRINT MENU 7 Check the Top of Form (see below). Important Notes Regarding the Top of Form (TOF) Setting 2 Lift up the paper separator. The Top of Form is where the printing begins on the page. The factory setting is 1 inch down from the top of the page. !! 3 Load the paper on the tractors: pull levers (1) to unlock, open covers (2), place paper holes on pins (3), close covers, adjust distance between tractors and push levers back to lock. If you turn the platen knob when the printer is on, you will cause the Top of Form to mis-align. Always shut the printer off before turning the platen knob. Press LF/GROUP until you see the paper path you are using. Press FF/LOAD/ITEM until Page Width appears. Press TEAR/SET to change the setting to 13. 6". Hold SHIFT and press SEL to exit the Menu. See "Menu Mode" under "Section 3: Using Your Printer" in the on-line User's Guide for more information. 3 Press and hold the LF key while turning the printer back on. A sample of available typefaces will print, then the test will end automatically. Selecting a Printer Driver ! See your software documentation for instructions on how to install a printer driver. Before you can use your printer, you must select the correct printer driver in your software. [. . . ] A sample of available typefaces will print, then the test will end automatically. Selecting a Printer Driver ! See your software documentation for instructions on how to install a printer driver. Before you can use your printer, you must select the correct printer driver in your software. If you select the wrong driver, you will see strange characters, incorrect fonts, etc. Printer Drivers for GP ULTIMA ST SPORTS Series Emulation IBM Proprinter III (factory setting) Select Driver* Okidata GP ULTIMA ST SPORTS/1 IBM IBM Proprinter III IBM Proprinter II IBM Proprinter Okidata GP ULTIMA ST SPORTS/1 Epson Epson FX850/1050 Epson FX86/286 Epson FX Okidata Microline 520/521 Okidata Microline 320/321 Okidata Microline 292/293 Epson FX Setting the Emulation Your printer has three emulations: Models GP ULTIMA ST SPORTS, ML51 Emulations · IBM® Proprinter III--factory setting · Epson® FX · Okidata MICROLINE Standard · Epson LQ--factory setting · IBM Proprinter · IBM AGM ® Okidata MICROLINE Standard * Select a driver from as close to the top of the list as possible. Printer Drivers for ML590 Series Emulation Epson LQ (factory setting) Select Driver* Okidata ML 590/1 Epson Epson LQ 870/1170 Epson LQ 800/1000 Epson LQ 2500 Okidata ML 590/1 IBM IBM Proprinter X24e/XL24e IBM Proprinter X24/XL24 IBM Proprinter Use only when you've selected an IBM Proprrinter X24e/SL24e driver and you need to use Epson LQ high densiy graphics. ML590, ML591 IBM Proprinter To set your printer to the appropriate emulation: 1 Make sure paper is loaded. 2 Press SHIFT + SEL to enter the Menu mode. [. . . ]