User manual KYOSHO INFERNO GT2

[. . . ] Contact a local dealer to purchase optional items. Unpacking LCD Display Introduction Manuals Quick Setup Guide Warranty Card (Not available in all locations) User's Guide Cables Power Cord Others D-Sub Cable Remote Control (BP59-00138B) Batteries (AAA X 2) (Not available in all locations) Sold separately Semi Stand KIT LAN Cable USB Cable RGB to BNC Cable RGB to COMPONENT Cable Network Box Introduction Sold separately Wall Mount KIT TV Tuner Box Your LCD Display Front SOURCE button Switches from PC mode to Video mode. Selects the input source that an external device is connected to. [PC] !' [ DVI] !' [ AV] !' [ Component] !' [ [DisplayPort] !' [MagicInfo] !' [TV] Note · The RGB/COMPONENT IN port is compatible with RGB (PC) and Component signals. However, the picture may display abnormally if the connected external input signal is different from the selected video signal. [. . . ] TV channels provide written information services via teletext. - Teletext Buttons TTX/MIX - This is activated when a TV tuner box is installed. MTS/DUAL MTSYou can select MTS (Multichannel Television Stereo) mode. Audio Type FM Stereo Mono Stereo SAP DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV. - This is activated when a TV tuner box is installed. ENTER/PRE-CH This button is used to return to the immediately previous channel. - This is activated when a TV tuner box is installed. MUTE Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio MTS/S_Mode Mono Mono !" Stereo Mono !" SAP Default Manual Change Mono Introduction comes back on if MUTE or - VOL + is pressed in the Mute mode. - This is activated when a TV tuner box is installed. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display . Press SOURCE on the product or remote control and select "AV". Then, start the Camcorders with a tape inserted. 2. 3. 4. Note The audio-video cables shown here are usually included with a Camcorder. For more information on how to purchase and install a network box, contact Samsung Electronics. Connections Connecting the Power Connect the [POWER] terminal of the product and the [POWER] terminal of the installed network box using a power extension cable. Connect the power cord to [POWER] on the network box and mains socket. Turn on the power switch. Connecting to MAGICINFO OUT Connect the [MAGICINFO OUT] terminal of the network box and the [HDMI IN 2 (MAGICINFO)] terminal of the monitor using the HDMI cable. Connections Connecting a LAN Cable 1. Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your PC. Connecting a USB devices 1. You can connect USB devices such as a mouse or keyboard. Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. The figure shown below ("No Signal") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the SelfTest mode, the LED power indicator remains green and the figure moves around on the screen. 4. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Warning Messages You can even view the screen at a resolution of 1920 x 1080. [. . . ] (Refer to the Connecting a Computer) A: Q: A: A: Q: A: Check the volume level. If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Q: A: The remote control buttons do not respond. [. . . ]