User manual KYOSHO INFERNO GT2 ASTON PARTS LIST

[. . . ] 1993, 1995, 1996, 1997, 1998, 2001 by KYOSHODATA Revised edition, September, 2001 Written and produced by the KYOSHODATA Training & Publications Department. Please address any comments on this publication by mail to: Training & Publications Department Okidata, Div. Mount Laurel, NJ 08054-4620 or by e-mail to: pubs@okidata. com We welcome you to visit our web site: http://www. okidata. com Year 2000 Compliance All products currently sold by Okidata are Year 2000 Compliant. Each product contains information technology that accurately processes date and time data between the years 1999 and 2000. [. . . ] This can cause loss of data and damage the printhead. Sets the signal on pin 18 to +5V (factory default) or Open. Choose character width measured in characters per inch (cpi). Change to Yes if you wish to print the DEL code (decimal 127) as a solid box. Choose NLQ Courier or NLQ Gothic font for letter quality printing, utility (factory default) for faster draft printing, or HSD for fastest printing (lowest quality). Change the setting as required to obtain the best registration for bi-directional printing. E-30 Section 3 4 Form Tear-Off. Choose 500ms, 1 sec, or 2 sec to turn this feature on and select a time interval for the printer to wait before advancing the paper. don't want these settings changed from the control panel. This feature also prevents normal access to the Menu. To access the Menu, turn the printer off, then hold down the SEL key while turning the printer on. Print Suppress Effective. If you system uses the DC1 and DC3 codes for something other than the print suppress mode, change the setting to No. Fine tunes the automatic setting of the printhead gap. This extra paper movement can cause uneven print registration in graphics. If you have this problem, use the menu to deactivate Forms Tear-Off. ! Never engage Forms Tear-off when printing on labels! The Forms Tear-off feature automatically moves the paper up to the tear position after the selected interval. When the printer receives data, it will move down to the initial printing position. E-32 Section 3 4 Forms Tear-off Feature PARK QUIET TOF PRINT If you have problems setting the Top of Form high enough on the page when using Forms Tear Off, see "Problem Solving. " 2. Swing the wire guide up into the paper separator, and swing the separator upright. Move the paper lever to "TOP. " 4. Press FF/LOAD to remove single sheet from paper path if needed. Lower the paper separator and swing the wire guide out. Move the paper lever to "REAR" or "BOT, " as appropriate. When you switch paths, the printhead travels and gently fires pins to sense paper thickness and set the gap. Switching Paper Paths To switch to single-sheet feed: 1. Tear off any printed pages, then press PARK. 4 4 Paper Park Feature If you have continuous-form paper loaded and you wish to switch to another paper path, first tear off the printed pages, then press the PARK button. The continuous-form paper will immediately retract from the paper path. PARK PRINT Using Your Printer E-33 Section 4: Problem Solving Problem: Nothing happens when I turn on the printer. [. . . ] 2-3 SI select pitch menu items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 31 Single sheet paper jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 loading . . . . . . . . . . . . . . . . . . . . . . . 10-11 switching to continuous forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Size menu item . . . . . . . . . . . . . . . 26, 31 Skip over perforation commands . . . . . . . . . . . . . . . . . . 50, 54 menu item . . . . . . . . . . . . 26, 27, 31 Slashed zero . . . . . . . . . . . . . . . . . . . . 26, 31 Software I-Prime commands . . . . . . . . . . . . . . . 50, 52, 54 Stop printing command . . . . . . . . 52 Style menu item . . . . . . . . . . . . . . 26, 31 Subscript commands . . . . . . . . . . . . . . . 50, 52, 54 Superscript commands . . . . . . . . . . . . . . . 50, 52, 54 Index E-55 T TEAR button . . . . . . . . . . . . . . . . . . . . . . . . 20 Tear feature . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Time out print menu item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 31 Time, wait, menu item . . . . [. . . ]