User manual KYOSHO INFERNO MP-7.5 SPORTS 4

[. . . ] Note · · Remove the Styrofoam and vinyl cover. After unpacking the package, make sure to check the contents of the package. Make sure to keep the package box for transporting the product in the future. Introduction Unpacking LANDSCAPE type Manuals PORTRAIT type Quick Setup Guide Warranty Card (Not available in all locations) User's Guide, MagicInfo Software CD, MagicInfo Manual CD Cables D-Sub Cable Others Power Cord Remote Control Batteries (AAA X 2) (Not available in all locations) Sold separately DVI Cable Wall Mount KIT LAN Cable (Applicable to the DRN-S model only) Introduction Your LCD Display Front Power button [ D. MENU ] Use this button for turning the LCD Display on and off. Note This is available when a TV tuner box is installed. SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time. [. . . ] Use the 5. 0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A. To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) 1. Remove the 4 screws on the back of the product. Introduction 2. Insert the screw B into the plastic hanger. Notice · · · 3. Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. Be careful when installing the product on the bracket as fingers can be caught in the holes. Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product. 4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. Introduction ABC- LCD Display Wall Bracket Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. 2. Fix the product to the wall bracket. · · Do not use benzene, thinner or other flammable substances, or a wet cloth. We recommend that a KYOSHO cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Troubleshooting Clean with a soft cloth (cotton flannel) smoothly. · Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface. ) · The user will be required to pay costs and related expenses for repairing damages caused. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer. Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting. (If it does, request an a service for the main board of the computer. ) 3. If you installed a new video card or if you assembled the PC, check if you installed the Adaptor(video). Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz. [. . . ] (For example, the HP USB Disk Storage Format Tool) 2) Copies the OS ghost image and executables to your USB disk. 3) Enter the BIOS menu of your set by pressing the F2 key in the BIOS logo screen. Then, enable the USB Boot First option by selecting that option and pressing the Enter key in the Boot menu. 4) Switch your set on while your USB disk is connected and boot up in DOS mode. [. . . ]