User manual KYOSHO NISSAN GT-R GT500 2008

[. . . ] While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the Oki Data website http:// www. okidata. com and http://my. okidata. com. As an ENERGY STAR® Program Participant, the manufacturer has determined that this product meets the ENERGY STAR guidelines for energy efficiency. Oki is a registered trademark of Oki Electric Industry Company Ltd. [. . . ] · Up to 64 print instruction information can be displayed. · If two or more types of print languages/modes are set up on a single workstation, identical job numbers may be displayed when an inquiry command (lpstat) is issued. Sample To inquire about the print data received by a printer set up as "P001", enter the following command: %lpstat -o P001 6. 4 Printing (HP-UX/Solaris) 33 6. 5 -C Option (lpr Command) This section explains the functions which can be specified and printing operations which will be affected by the -C option. The -C option is available only when the SunOS directs the printer to enter the spool mode. Important · When the PostScript logical printer that was configured on the OkiWebRemote and -C option of "lpr" command have been specified simultaneously, some of the actiions cannnot be guaranteed to wprk. Also, when specifying the PostScript logical printer as a default printer on Unix, it is recommended not to user the -C option by "lpr" command. Function The following items can be set up by using the -C option: Note · Any parameter other than below becomes invalid if specified. Selecting a Paper Tray When selecting a paper tray, either the paper size or the tray itself is specified. If the paper size is specified, the printer automatically searches and selects the tray where the specified paper is loaded. The following parameters can be specified: Parameter INTRAY1/intray1 INTRAY2/intray2 INTRAY3/intray3 INTRAY4/intray4 A4/a4 B5/b5 A5/a5 LETTER/letter LEGAL/legal Selects Tray 1. Selects the tray where A4 paper is loaded. Selects the tray where B5 paper is loaded. Selects the tray where A5 paper is loaded. Selects the legal size (8. 5 × 14). Description Note · If several parameters are specified in one "lpr" command, data may not be printed correctly. To specify multiple parameters, separate them with ", ". For example, to output a file named "file1" 2-sided on A4 to printer "P001", enter the following command: %lpr -P P001 -C, DUP, A4 file1 Important · If the command specified by the -C option exceeds 64 characters, the operation may not function correctly. 6. 5 -C Option (lpr Command) 37 7 7. 1 Printing From a Macintosh Computer Printing From a Macintosh Computer This section explains the installation procedure for printing from a Macintosh computer. System Configuration As the printer supports EtherTalk and LPD protocol, you can print from Macintosh. Note · Printing using the LPD protocol is available only with the Mac OS X. Target Computers The printer supports a Macintosh or Power Macintosh with the following OS: · Mac OS 8. 6 through 9. 2. 2 · Mac OS X Refer to · User Guide (PostScript Driver) Set Up Procedure The setting procedure is as follows: 1. Setting up the printer Use the printer control panel or OkiWebRemote to set the following port to [Enable]. · Printing through LPD: LPD port (default: [Enable]) · Printing through EtherTalk: EtherTalk port (default: [Disable]) Note · For details on how to set the port, refer to the Setup Guide. · OkiWebRemote allows more detailed settings. 2. Setting up the Macintosh Install the printer driver(Adobe PS) for Macintosh. Install the screen font if necessary. Refer to · User Guide (PostScript Driver) 38 7 Printing From a Macintosh Computer 8 8. 1 Network Utility Software IP Address Setting Tool You can set the printer's IP address by using the IP Address Setting tool. You can easily connect the printer to a network with a TCP/IP environment. This tool searches a network for a printer that has been assigned an IP address by a server such as a DHCP server, then sets the printer's IP address. Also, this tool enables you to set a printer that is connected to a network without a DHCP server by specifying the MAC address. This tool can be used by starting it from the CD-ROM. Refer to · For details about how to use the IP Address Setting Tool: Online Help for the tool 8. 2 NetWare Setup Wizard You can set or change the initial settings for the NetWare server and the printer by using the NetWare Setup Wizard. This tool can be used when setting the printing environment by using the NetWare server. [. . . ] · The address information can also be retrieved automatically via the BOOTP or RARP servers. For such cases, change the [Get IP Address] selection on the control panel to [BOOTP] or [RARP]. · Depending on the network environment, you may need to set the subnet mask and gateway address. · Please check with your network administrator if you have any questions concerning your network environment. [. . . ]