User manual KYOSHO PIPER J3 CUB 40 PARTS_LIST

[. . . ] Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer . While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information _______________________________ Oki and Microline are registered trademarks of Oki Electric Industry Company Ltd. Apple, Macintosh and Mac OS are registered trademarks of Apple Computers Inc. [. . . ] To activate Form Tear-Off, change the setting to On. The Forms Tear-Off feature allows a printed continuous form page to be torn off without wasting paper or adjusting the printer. For more information, see page 61. Front Load Adj. For fine tuning the Top of Form (TOF) location when using continuous forms (front feed). Settable from -40 to +40 in increments of 1/120 inch. Negative values decrease the space down from the top of the form: · TOF moves up · paper moves down. Positive numbers increase the space down from the top of the form: · TOF moves down · paper moves up. Gap Control Sets whether the printhead gap is set automatically [the default] or manually. Microline 8480FB User's Guide · 44 Manual Gap Settings Setting Manual Gap 1 Used for · Single sheets 14 to 22 lb. US Bond (52 to 81 g/m2) · Thickness range 0. 06 to 0. 10 mm · Single sheets 22 to 34 lb. US Bond (81 to 128 g/m2) · 2-Part Multi-Part Forms (carbon-backed) · Thickness range0. 10 to 0. 15 mm · Single sheets 34 to 42 lb. US Bond (128 to 156 g/m2) · 3-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 15 to 0. 20 mm · Postcards · 4-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 20 to 0. 25 mm · 5-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 25 to 0. 30 mm · 6-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 30 to 0. 35 mm · 7-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 35 to 0. 40 mm · 8-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 40 to0. 45 mm · Heavy paper, 0. 45 to 0. 50 mm thick · Heavy paper, 0. 50 to 0. 55 mm thick · Heavy paper, 0. 55 to 0. 60 mm thick · Heavy paper, 0. 60 to 0. 65 mm thick · Heavy paper, 0. 65 to 0. 70 mm thick Manual Gap 2 Manual Gap 3 Manual Gap 4 Manual Gap 5 Manual Gap 6 Manual Gap 7 Manual Gap 8 Manual Gap A Manual Gap B Manual Gap C Manual Gap D Manual Gap E Gap Pos. When Auto Gap detection is enabled, this sets how far in from the left edge of the form the gap detection begins: 2 inches (51 mm) [the default] or 4 inches (102 mm). Microline 8480FB User's Guide · 45 Graphics The default is Bi-directional. Changing to Uni-directional will improve the print registration, but slow the print speed. High Skip The default is Yes. This enables the low-vibration mode, which reduces printer vibration during printing. Positive values stop the printing further up on the form: · Paper End moves up · paper moves down PE Pos. [Paper End Position] This sets when the the printer will move to the next continuous form, based on the distance between the center of the characters on the last line of the form and the bottom of the form. Available settings: 3. 18 mm (1/8") or 6. 35 mm (1/4") [the default]. Pitch Choose the character width, in characters per inch (cpi): 10 [the default], 12, 15, 17. 1, or 20 cpi. Power Save Time Sets the time the printer waits before entering the Power Save Mode when Power Saving is set to Enable [the default]: 5 min, 10 min [the default], 15 min, 30 min, or 60 min. Power Saving Sets whether or not the printer enters the energy-saving Power Save Mode after the interval specified under Power Save Time. Cmd. The default is Valid: the printer will recognize a command for unidirectional printing. Change to Invalid if you do not wish the printer to recognize uni-directional printing commands. Microline 8480FB User's Guide · 49 Print Mode Choose the print quality and speed: LQ Courier [the default], LQ Roman, LQ Swiss, LQ Swiss Bold, LQ Orator, LQ Gothic, LQ Prestige, or Utility. Print Suppress The default is No. If your system uses the DC1 and DC3 codes for print suppress mode, change the setting to Yes. Prop. Choose Yes to engage proportional spacing of characters. Quiet The default is Invalid. Choose Valid to reduce printing noise. Rcv. Buffer Sets the amount of memory ( 0 or 128 Kbytes) devoted to holding received data. Changing this to 0 will tie up your computer while printing, but if you abort the print job, the printer will stop much sooner. Regist. Low Adjusts the print registration for low-speed printing. [. . . ] Open the platform and use a clean, dry cloth to clean away any bits of paper and paper dust. F5-03b. JPG 3. Tilt the display panel forward and remove the ribbon cartridge. F2_18a. JPG 6. Use a clean, dry cloth to clean any bits of paper or paper dust from around the platen. Microline 8480FB User's Guide Maintenance · 81 7. Replace the ribbon cartridge (see page 76 for more information) and tilt the display panel back into place. [. . . ]