User manual KYOSHO PIPER J3 CUB 50EP PARTS LIST

[. . . ] 7 PRODUCT LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 BACK LABEL 5 6 7 8 9 SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 PIPER J3 CUB 50EP PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SETUP LAN, WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The default SSID of the router is "default". Do not modify default value if you don't know what it is, default setting is `Auto 20/40 MHz'. Select the upper band or lower band for your radio frequency. While upper band is selected, the channel number you can select is from channel 5 to channel 11. While lower band is selected, the channel number you can select is from channel 1 to channel 7. It is the radio channel used by the wireless LAN. All devices in the same wireless LAN should use the same channel. Please select the country you are located and designate a channel that the router will use. If you want to let the router automatically to find an available channel with the highest signal strength, please select "Auto". Set the maximum output power of the router. The higher output power, the wider coverage range. To use RADIUS, enter the IP address of the RADIUS server, the RADIUS port (default is 1812) and the shared secret from the RADIUS server. Please refer to "Authentication RADIUS Server" setting below for RADIUS setting. Personal (Pre-Shared Key) ­ Pre-Shared Key authentication is based on a shared secret that is known only by the parties involved. To use WPA Pre-Shared Key, select key format and enter a password in the "Pre-Shared Key Format" and "Pre-Shared Key" setting respectively. Pre-Shared Key You may select to select Passphrase (alphanumeric format) or Format Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the Pre-shared Key. For example: Passphrase: "iamguest" Hexadecimal Digits: "12345abcde" Pre-Shared Key Please enter 8-63 characters as the "Pre-Shared Key". Authentication Enter the port (default is 1812), the IP address and the RADIUS Server password of external RADIUS server are specified here. When you finish, click `save' to save the settings made and restart the router so the settings will take effect after it reboots. Wireless ACL This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network. Parameter Active Actions Description Choose to either Enable ­ Enabled the Wireless Access Control Disable ­ Disable the Wireless Access Control Allow ­ Only allow the wireless clients with the MAC Address you have specified can access to the router. Deny ­ The wireless clients with the MAC Address you have specified will be denied accessing to the router. MAC Address Enter the MAC Address of the wireless clients for the filtering control. When you finish, click `save' to save the settings made and restart the router so the settings will take effect after it reboots. 13 Advanced Settings The advanced settings pages allow users to modify the more complex features of this device. Advances wireless This page allows advanced users who have sufficient knowledge of wireless LAN. These setting shall not be changed unless you know exactly what will happen for the changes you made on your router. Parameter Beacon Interval Fragmentation Threshold RTS Threshold Description The interval of time that this wireless router broadcast a beacon. Beacon is used to synchronize the wireless network. The range for the beacon period is between 20 and 1024 with a default value of 100 (milliseconds). [. . . ] Computers use numbers called port numbers to recognize a particular service/Internet application type. The Virtual Server allows you to re-direct a particular service port number (from the Internet/WAN Port) to a particular LAN private IP address and its service port number. Local IP This is the LAN client/host IP address that the Public Port number packet will be sent to. Start port Here the starting port number must be entered End port Here the end port number must be entered Note : The ports from the start port till the End port will be opened Click the `edit icon' to change an existing rule. Click `Apply' for the changes to take effect. 15 TOOLBOX Settings Sitecom Cloud Security Antivirus software alone is not safe enough. [. . . ]