User manual KYOSHO YAK-54 BLS EXPLODED VIEW

[. . . ] Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, press the button to adjust volume. [. . . ] Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Current picture information is displayed on the upper left corner of the screen. In TV mode, these buttons can be used to configure a list of channels. Introduction You can select the PC, DVI, HDMI or DP(DisplayPort) external input directly in a mode other than TV mode. TTX/MIX TV channels provide written information services via teletext. - Teletext Buttons Note This function does not work for this LCD Display. MTS/DUAL MTSYou can select MTS (Multichannel Television Stereo) mode. Audio Type FM Stereo Mono Stereo SAP DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV. Note Enabled when a TV tuner box is connected. ENTER/PRE-CH This button is used to return to the immediately previous channel. Note Enabled when a TV tuner box is connected. MUTE Pauses (mutes) the audio output temporarily. They are usually found on the side or back of the camcorder. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV IN] on the LCD Display . Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [L-AUDIO-R]] on the LCD Display . 2. Connections 3. 4. Press SOURCE on the product or remote control and select "AV". Then, start the Camcorders with a tape inserted. Note The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store. ) If your camcorder is stereo, you need to connect a set of two cables. Connecting Using a HDMI Cable 1. Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] on the product and the HDMI output port on a digital device. Turn on the power switch. Connections Connecting to MAGICINFO OUT Connect the [MAGICINFO OUT] terminal of the network box and the [HDMI IN 2 (MAGICINFO)] terminal of the monitor using the HDMI cable. Connecting a LAN Cable Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your PC. Connections Connecting a USB devices You can connect USB devices such as a mouse or keyboard. Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. The figure shown below ("No Signal") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen. 4. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Warning Messages You can even view the screen at a resolution of 1920 x 1080. [. . . ] If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software Program. Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Q: A: A: A: A: A: The remote control buttons do not respond. Check the polarities (+/-) of the batteries. [. . . ]