User manual LA CROSS TECHNOLOGY FX6000

[. . . ] Your FX6000 is carefully designed and produced for outdoor activities, in order to utilize the features of your watch, it is advisable to read the following instructions: - Read the instruction before you use the FX6000. - Avoid exposing your FX6000 to extreme conditions for an unreasonable time. - Avoid rough uses or severe impacts to your FX6000. - Do not open the FX6000's case unless a certified service agency because your FX6000 contains precise electronic sensor and components. [. . . ] - The timer starts to beep every second when it is 5 seconds to the end of the countdown. -When the countdown time reaches zero, a long beep lasting for 2 seconds will be heard. - Press any button in this period to terminate the beep sound prematurely. -When the countdown time reaches zero, press [compass] button to re-load the preset time, or press [start/stop] button to re-load the preset time and start the countdown simultaneously. To Reset the Timer - Press and hold the [compass] button for 2 seconds to reset the timer while the timer is stopped. . Countdown Timer Mode indicator Pre-set countdown time analog second Countdown Timer Mode start/stop the countdown time Countdown Timer 'running' Mode 15 9. 0 Pacer Mode - Pacer Mode Pacer Mode the number of bpm (Beep per minute) Pacer Mode indicator Pacer Mode hold mode digits have been selected (flashing) - The FX6000 has a build-in a pacer for the user: The Pacer Mode. - The minute digits flash on the display because they are being selected. The Setting Procedures - Press [mode] button to change the selections following the Dual Time Setting Sequence shown on the left. - If the digits are flashing, press the [start/stop] button to increase the number; hold the [start/stop] button to change the number at a higher speed. Press the [Compass] button to decrease the number; hold the [Compass] button to change the number at a higher speed. - After you set the Dual Timer, press the [mode] button to exit the Dual Time Setting Sequence. - The bearing will be 3238 (MB) - 238 (W) = 3008 (TB). Example 2 - 228 Easterly magnetic declination and the compass needle points 2788. - The bearing will be 2788(M) + 228(E) = 3008 (TB). - FX6000 will compensate the compass bearing wherever the magnetic declination is either Westerly (-ve) declination or Easterly declination (+ve) automatically, if the user inputs the magnetic declination angle of the city which is close to the user's current location during the calibration. - Check the 'Calibrating the Compass' section for more details on the calibration. true bearing 3008 magnetic bearing 2788 point A Compensate the Bearing at a place with Easterly (E) Magnetic Declination 23 11. 4 Compass Mode - Magnetic Declination at Major Cities No. Country/Place Declination 1 Afghanistan Kabul 2 Australia Canberra 3 Austria Vienna 4 Bahrain Manama 5 Bangladesh Dhaka 6 Belgium Brussels 7 Brazil Brasilia 8 Canada Ottawa 9 Chile Santiago 10 China Beijing 11China Hong Kong 12Costa Rica San Jose 13Cuba Havana 14Czech Republic 15Denmark Copenhagen 16Egypt Cairo 17Finland Helsinki 18France Paris 19Germany Berlin 20Greece Athens 21Hungary Budapest 22India New Delhi 23Indonesia Jakarta Jerusalem 24Israel 25Italy Rome 26Japan Tokyo 27Jordan Amman 28Kenya Nairobi 29Korea Seoul 30Malaysia Kuala Lumpur 31Mexico Mexico City 32Nepal Kathmandu Major City 2-E 12-E 2-E 2-E 0 1-W 19-W 14-W 5-E 6-W 2-W 0 3-W Prague2-E 1-E 3-E 6-E 1-W 1-E 3-E 4-E 1-E 1-E 3-E 1-E 7-W 3-E 1-E 7-W 1-E 6-E 0 No. Country/Place Major City 33Netherlands Amsterdam 34New Zealand Wellington 35Norway Oslo 36Pakistan Islamabad 37Philippines Manila 38Portugal Lisbon 39Russia Moscow 40Singapore Singapore 41South Africa Cape Town 42Spain Madrid 43Sweden Stockholm 44Switzerland Bern 45Taiwan Tai-pei 46Thailand Bangkok 47UAE Abu Dhabi 48United Kingdom 49United States Washington, DC 50 Juneau 51 Phoenix 52 Little Rock 53 Sacramento 54 Denver 55 Atlanta 56 Honolulu 57 Boston 58 Saint Paul 59 Jackson 60 Santa Fe 61 Oklahoma City 62 Salem 63 Harrisburg 64 Salt Lake City Declination 1-W 22-E 0 2-E 1-W 5-W 9-E 0 23-W 3-W 3-E 0 3-W 0 1-E London3-W 10-W 25-E 12-E 2-E 16-E 10-E 4-W 10-E 16-W 2-E 1-E 10-E 6-E 18-E 11-W 14-E 24 11. 5 Compass Mode - Before Calibrate the Compass To Calibrate the compass - Perform the compass calibration in the following conditions: 1) when the XG- 20 is used the first time, 2)when the 'DIST' indicator is flashing, 3) the battery has been replaced, 4) when using the compass in a location different from the place in which the compass had been calibrated. IMPORTANT: If the watch has not been calibrated, the direction reading may be inaccurate. - Check the 'Magnetic Declination at Major Cities' section to get the magnetic declination of the city closeest to your current location * * Compass Mode Compass button hold mode 1 minute mode button mode button Magnetic Declination Setting Mode Calibration 'Rotation' Mode Calibration Sequence 25 11. 6 Compass Mode - Calibrating the Compass finish start Calibration 'Rotation' Mode To Calibrate the Compass - Press and hold the [mode] button for 2 seconds to start the Magnetic Declination Setting, in the Compass Mode. - The 'DEC' indicator will be appeared on the 1st row of the display. The digit will start flashing, press the [start/stop] button to change the angle (from -90 to 90), until the desire magnetic declination has appeared. [. . . ] NOTE: Auto-Light feature will consume more battery than that when the auto-light feature is disable, hence a shorter life cycle for the battery when the auto-light feature is enabled. To Enable/Disable Auto-Light - Press and hold for 2 seconds to enable the auto-light feature when the auto-light is disabled. - Press and hold for 2 seconds to disable the auto-light feature when the auto-light is enabled. TM low battery indicator Low Battery Indication TM auto-light indicator Auto-light Indication 34 13. 0 Specifications Current Time Mode Time System: - AM, PM, Hour, minute, second, and display with bar graph animation at the rate of 1 second - 12-hour or 24-hour format Calendar: - Month, date and day of week display - Auto-Calendar function for leap year and day of week Alarm Mode Alarm Type: - 1 daily alarms, hourly chime Alarm Sound: - Sounds for 20 seconds at preset time of real time clock Chronograph Mode Resolution: - 1/100 second Range: - 9 hours 59 minutes 59. 99 seconds Lap memory: - 42 lap memories (maximum) Countdown Timer Resolution: - 1 second resolution Range: - 99 hours 59 minutes 59 seconds Operation Mode: - Countdown to zero and stop at zero Timer Sounds: - Beeps once when count to last 10, 5 and 1 minute - Beeps once for every second when count to last 5 seconds, - Sounds for 2 seconds when count to zero Pacer Mode Range: - 40 bpm to 180 bpm Pacer Sounds: - Pacer beep Dual Time Mode Time System: - AM, PM, Hour, minute, second, and display with bar graph animation at the rate of 1 second Calendar: - Month and date WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. [. . . ]