User manual LA CROSS TECHNOLOGY K2-100

[. . . ] GB K2 EXTREME K2-100 1. 0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. 0 The K2-100 Parts and Its Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3. 0 Major Function Modes - Time Keeping, Altimeter and Barometer Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4. 0 Time Keeping Mode and its Sub-displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] measures Normal and Relative 5. 7 Altimeter Mode - Ascending and Descending Rate of the 24 Hour Memory Ascending and Descending Rate The K2-100 has a built-in function for calculating the ascending and descending rate of the Altitude of the last 24 hours. T h e a s c e n d i n g a n d d e s c e n d i n g r a te i s t h e a l t i t u d e difference between two memory records. A (+) value implies ascending rate; a (-) value implies a descending rate. These rates can be reviewed in the Ascending/ Descending Rate Display. adjust button adjust button adjust button hold adjust - Normal altitude is the difference between your current altitude and SEA LEVEL. (Assuming that air pressure at sea level is 1013. 21mbar). Relative altitude is the difference between your current altitude and the altitude of a specific altitude level at which you set the altimeter to 'Zero'. To use relative altitude, for example, measure the altitude difference between the starting point and the finish points of a trek. adjust button adjust button adjust button mode button adjust button - hold adjust Altitude Graph Display mode button twice Altitude Graph Display - Review the Ascending and Descending Rate ascending or descending rate - To measure the altitude difference, set the K2-100 to Relative Altitude display at the starting point of the trek, the K2-100 will automatically set the altitude to 'Zero'. Check the altitude at the finish point of the trek, the K2-100 will show the altitude difference on the display. Press the [adjust] button three times to select the Ascending / Descending Rate Display, in the Altitude Graph Display. While the Ascending / Descending Rate Display is shown, the Altitude Ascending or Descending Rate shows on the 1st row of the display. The altitude memory and temperature show on the 2nd row of the display. The time that the memory was recorded shows on the 3rd row of the display. P r e s s t h e [ l a p / r e s e t ] b u t t o n t o v i e w t h e me mo r y b y backward scrolling ( from -15 min. to 24 hour), press the [start/stop] button to view the memory through forward scrolling (from -24 hour to -15 min. ). While these displays are shown, press the [mode] button to exit the reviewing and the display will return to the Altitude Graph Display. - - lap/reset button - To Switch between the Normal and Relative Altitude Press and hold the [adjust] button for 2 seconds to enter Altitude Setting Display. Press the [adjust] button four times to select the Normal / Relative Altitude Display. Press and hold the [adjust] button to enter the setting display of the Normal / Relative Altitude Display. Press the [lap/reset] button to switch between the Normal and Relative Altitude. After you set the altitude, press the [mode] button to exit the setting sequence. Press the [mode] button once again to return to the Altitude Graph Display. Ascending / Descending Rate Display start/stop lap/reset - lap/reset button Relative Altitude Display Normal Altitude Display Relative Altitude Setting Sequence To view the memory by forward scrolling (from -24 hour to -15 min. ) To view the memory by backward scrolling (from -15 min. to -24 hour) - 20 22 21 GB 23 GB 5. 6 Altimeter Mode - 24 Hour Memory (the History Graph) 24 Hour Memory The K2-100 has two altitude memory functions: the 24 Hour Memory and the User Log Memory. 24 Hour Memory automatically records the altitude for every 15 minutes of the last 24 hours. These figures can be reviewed in Memory Display. [. . . ] To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. [. . . ]