User manual LA CROSS TECHNOLOGY WS-8011UM

[. . . ] WS-8011UM with TX2U 433 MHz Radio Controlled Temperature Clock Battery Cover Instruction Manual WS-8011UM with TX2U 433 MHz Radio Controlled Temperature Clock Pages 2 through 12 ------------------------------------------------------------------------------------ Battery Cover Battery Cover WS-8011UM with TX5U 433 MHz Radio Controlled Temperature Clock Pages 14 through 26 2 TABLE OF CONTENTS Topic Inventory of Contents/ Additional Equipment About WWVB Quick Set-Up Guide Detailed Set-Up Guide Battery Installation Program Mode Function Buttons Time Zone Setting DST (Daylight Saving Time) Setting Language Selection Time Setting Calendar Setting 12/24-Hour Setting Selecting F or C Features & Operations Changing Display Mode (seconds, temperature) The Alarm Indoor Temperature Remote Temperature Mounting Maintenance & Care Troubleshooting Specifications Warranty Information INVENTORY OF CONTENTS Page 3 3 3 4 5 5 6 6 6 7 7 7 7 8 8 8 9-10 10 11 11 12 1) WS-8011UM 2) TX2U Remote temperature transmitter 3) Instruction manual and warranty card. ADDITIONAL EQUIPMENT (not included) 1) 2) 3) 4) Two fresh 1. 5V AA batteries. Appropriate screwdriver for screws. ABOUT WWVB (Radio Controlled Time) The NIST (National Institute of Standards and Technology--Time and Frequency Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact time signal continuously throughout the United States at 60 kHz. [. . . ] A team of atomic physicists is continually measuring every second, of every day, to an accuracy of ten billionths of a second per day. These physicists have created an international standard, measuring a second as 9, 192, 631, 770 vibrations of a Cesium-133 atom in a vacuum. For more information about WWVB please see the NIST website at http://www. boulder. nist. gov/timefreq/stations/wwvb. htm QUICK SET-UP GUIDE Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. Have the indoor station and outdoor remote 3 to 5 apart. Batteries should be out of both units for 10 minutes. Place the batteries into the remote temperature sensor first then into the temperature clock. (All remote temperature sensors must be started before the temperature clock) DO NOT PRESS ANY BUTTONS FOR 10 MINUTES. 4. In this time the temperature clock and remote temperature sensor will start to talk to each other and the temperature clock will show both the indoor temperature and an outdoor temperature. If the temperature clock does not display both temperatures after the 10 minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed for 10 minutes you can place your remote temperature sensor outdoors and set your time. 15 16 The remote temperature sensor should be placed in a dry, shaded area. The remote temperature sensor has a range of 80 feet. Any walls that the signal will have to pass through will reduce distance. An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus resistance should not exceed 80 ft. NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must be avoided. To complete the set up of your temperature clock after the 10 minutes have passed please follow the steps below. DETAILED SET-UP GUIDE VI) BATTERY INSTALLATION Note: To avoid start-up problems make sure that the batteries do not spring free. A) REMOTE TEMPERATURE TRANSMITTER 1) Remove the battery cover. Place your thumb over the two air-vent slots on the face of the remote temperature sensor, push down gently, and slide battery cover down and off. 2) Observing the correct polarity, install 2 AA batteries. The batteries will fit tightly (to avoid start-up problems make sure that they do not spring free during installation). 3) Replace the battery cover. temperature, the date as "1/ 1", the weekday as "MON", and the remote temperature will be displayed (within three minutes). Also, the time will appear as "-:--" for approximately 1 minute. [. . . ] 5) If problems persist contact La Crosse Technology. Hour is incorrect (minute and date are correct). Be sure correct time zone and daylight saving time are selected. "--. -" appears in outdoor temperature LCD 1) Check batteries in the remote temperature sensor. [. . . ]