User manual LA CROSS TECHNOLOGY WS-8610

[. . . ] WS-8610 WIRELESS DATA LOGGING WEATHER STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this revolutionary 433MHz data logging weather station, which provides advanced datalogging and data-analysis functions for up to three outdoor temperature and humidity readings. The weather station is connectable to PC by the COM port and data importing to your PC is allowed. By utilizing the advanced software provided you might perform data analysis and statistics conveniently on your PC. With easy to use keys, this innovative product is ideal for home and professional usages. [. . . ] When the temperature or humidity is sensed to be out of the pre-set threshold value, the alarm will sound and the alarm icon will be present on LCD. You may press any key to stop the buzzer. If no key is pressed, the buzzer will beep for two minutes however the alarm signal icon will flash until the temperature or humidity is within the pre-set range again. Once an alarm is triggered, the display switches to the latest triggered temperature/humidity sensor channel. In addition, the high/ low limit icon and IN/ OUT icon is flashing as long as the alarm condition is met. If an alarm is triggered, the alarm icon will be flashing until the temperature and/or humidity is back to the conditions within the preset threshold values. The Alarm icon and the corresponding high or low alarm icons will flash once the current temperature or humidity is out of the pre-set threshold value 15 MEMORY CAPACITY The indoor weather station provides data-logging function. The temperature and humidity data are saved into the Memory of the indoor weather station at 5-minute intervals (recording one data set every five minute). The number of sets of data stored is shown at the ''mem'' display. The data-storing capacity for various numbers of remote temperature/humidity sensors used is listed below: No. of sets of temperature and humidity data stored for each transmitter and the indoor sensor ~3260 ~2510 ~2170 0 or 1 2 3 Note: · After the capacity has been reached, the first data (the oldest sets) will be overwritten by the latest one and so on. CLEARING DATA IN THE INDOOR WEATHER STATION CLEARING THE MAX/MIN TEMPERATURE AND HUMIDITY DATA OF A PARTICULAR REMOTE TEMPERATURE/HUMIDITY SENSOR CHANNEL To clear the max/min data of a remote temperature/humidity sensor channel: 1. Press the Plus or Minus key to select a remote temperature/humidity sensor channel. Press and hold the Mode key for 3 second. The maximum and minimum temperature/ humidity data and the time of record will be reset to the current value. CLEARING THE MAX/MIN TEMPERATURE AND HUMIDITY DATA OF ALL REMOTE TEMPERATURE/HUMIDITY SENSOR CHANNELS To clear the max/min data of all remote temperature/humidity sensor channels: 1. Press and hold the Mode key for 5 second. The maximum and minimum temperature/ humidity data and the time of record will be reset to the current value. CLEARING ALL STORED TEMPERATURE AND HUMIDITY DATA (FROM TEMPORARY MEMORY OF THE INDOOR WEATHER STATION) The on-going temperature and humidity data are stored at the ring buffer memory (a temporary memory area where the latest data will displace the oldest data once the memory capacity is reached). To clear this memory, the following step MUST be performed: 1. Press both the Plus key and SET key and hold for about 2 seconds. The temperature and humidity records of all temperature/humidity sensor channels (indoor and the outdoor temperature/humidity sensor channels) will be cleared. The average and history data will no longer exist. The memory display will show "mem 0000" after the data has been cleared. Note: The maximum/ minimum temperature and humidity data will not be cleared. 16 CLEARING ALL DATA AND SETTINGS OF THE INDOOR WEATHER STATION FROM THE PERMANENT MEMORY (FACTORY RESET) The factory reset needs to be launched if a malfunction of the indoor weather station occurs. [. . . ] To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. [. . . ]