User manual LA CROSS TECHNOLOGY WS-9021LLB-ITS

[. . . ] Contents Language Page _______________________________________________________________ English French Spanish 0 TABLE OF CONTENTS Topic INVENTORY OF CONTENTS QUICK SETUP DETAILED SETUP GUIDE BATTERY INSTALLATION 12 OR 24 HOUR TIME DISPLAY TIME SETTING FEATURES MIN AND MAX TEMPERATURE RESETTING MIN & MAX TEMPERATURE ADDING ADDITIONAL THERMO-HYGRO SENSORS VIEWING & OPERATING WITH MULTIPLE THERMO-HYGRO SENSORS MOUNTING TROBLESHOOTING MAINTENANCE AND CARE SPECIFICATION WARRANTY INFORMATION Page 1 This product offers: INSTANT TRANSMISSION is the state-of-the-art new wireless transmission technology, exclusively designed and developed by LA CROSSE TECHNOLOGY. INSTANT TRANSMISSION offers you an immediate update (every 4 seconds!) of all your outdoor data measured from the sensors: follow your climatic variations in real-time! 2 12 or 24 Hour Time Display Outdoor Temperature (°F or °C) Sensor signal reception icon Set/Channel Button Minimum/Maximum & Plus Button FIGURE 1 Low Battery Indicator Max icon 3 INVENTORY OF CONTENTS 1. Wireless Temperature Station (Figure 1) Wireless Temperature Sensor (TX29) and mounting bracket. (Figure 2) 3 each, 1/2" Philips screws. [. . . ] "MAX" icon appears at the bottom of the LCD and the maximum temperatures are displayed. 10 3. Press and release the min/max/+ button once more to return to the current temperatures. RESETTING THE MINIMUM AND MAXIMUM READINGS: User may reset the minimum and maximum temperature data to the current value by the following step: Press and hold the min/max/+ key for about 3 seconds to reset all the minimum/ maximum data of all channels and the indoor sensor to the current values in a single action. ADDING ADDITIONAL REMOTE SENSORS (OPTIONAL) The WS-9021U is able to receive signals from 2 additional temperature sensors . The following are instructions for the set-up of temperature sensor units with the WS-9021U. These extra sensors can be purchased through the same dealer as this unit. Remove all the batteries from the receiver and sensor(s) and wait 60 seconds. During these 60 seconds, press any button 20 times to discharge any excess power. Insert the batteries to the first temperature sensor. Within 2 minutes of powering up the first sensor, insert the batteries to the Temperature Station. Once the batteries are in place, all segments of the 11 LCD will light up briefly. Following the indoor temperature and the time as 12:00 will be displayed. If they are not shown in LCD after 60 seconds, remove the batteries and wait for at least 60 seconds before reinserting them. The outdoor temperature from the first sensor (channel 1) should then be displayed on the Temperature station. If this does not happen and the signal reception icon is not shown, after 2 minutes, the batteries will need to be removed from both units and reset from step 1. Insert the batteries to the second sensor as soon as the outdoor temperature readings from the first sensor are displayed on the Temperature station. NOTE: You must insert the batteries into the second sensor within 45 seconds of reception of the first sensor. The outdoor temperature from the second sensor and the "channel 2" icon should then be displayed on the Temperature station. If this does not happen after 2 minute, the batteries will need to be removed from all the units and reset from step 1. Insert the batteries to the third sensor as soon as the "channel 2" icon and outdoor data are displayed on the Temperature station. Then within 2 minutes, the channel 3 outdoor data from the third sensor will be displayed and the channel icon will shift back to "1" once the third sensor is 12 successfully received. If this is not happen, user shall restart the setting up from step 1. NOTE: You must insert the batteries into the third sensor within 45 seconds of reception of the second sensor. IMPORTANT: Transmission problems will arise if the setting for multiple sensors is not followed as described above. [. . . ] Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of 20 purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. [. . . ]