User manual LA CROSS TECHNOLOGY WS-9080U-IT

[. . . ] Topic Inventory of Contents Features Setting Up Battery Installation Function Keys LCD Screen and Settings Atomic Time -WWVB Radio Controlled Time Manual Settings Display of Indoor Temperature Reading Display of Outdoor Temperature Reading Display of Indoor Minimum and Maximum records Display of Outdoor Minimum and Maximum records Daily Indoor Minimum and Maximum Temperature display Daily Outdoor Minimum and Maximum Temperature display 915 MHz Reception Mounting Care and Maintenance Specifications Warranty Page 3 4 6 10 12 14 16 17 25 26 26 28 29 30 31 32 34 35 36 ) of all your outdoor data measured from the sensors: follow your climatic variations in real-time!Atomic Time function (WWVB Radio controlled time) or manual time setting options Atomic Time reception On/Off Daylight Saving Time ON/OFF 12/24 hour display Hour and minute display Calendar display Time zone option ±12 hours Wireless transmission at 915 MHz Outdoor signal reception intervals at 4-second Temperature display in degrees Fahrenheit (°F) or Celsius (°C) selectable Indoor and Outdoor temperature display with MIN/MAX recording (records can be reset) Can receive up to 3 outdoor sensors Daily minimum and maximum indoor temperature display Daily minimum and maximum outdoor temperature display Low battery indicator LCD contrast adjustable Table standing/ Wall mounting When one Sensor is used 1. First, insert the batteries into the temperature sensor. Immediately after and within 30 seconds, insert the batteries into Temperature Station (see "Install and replace batteries in the Temperature Station"). [. . . ] The following manual settings can be done in the setting mode: · °F/ °C temperature unit setting Press and hold the SET key for about 3 seconds to advance to the setting mode: The LCD contrast can be set to 8 different levels (0 to 7) to suit the user's needs (default LCD contrast setting is LCD 4). Press the + key or CH/- key to select the level of contrast desired. Press the SET key to confirm and enter the "Time Zone setting" or exit the setting mode by pressing the MIN/MAX key TIME ZONE SETTING: Using the + key or CH/- key, set the time zone. Press the SET key to confirm and enter the "Daylight Saving time ON/OFF setting" or exit the setting mode by pressing the MIN/MAX key. Use the + key or CH/- key to turn On or OFF the daylight saving time function. Confirm with the SET key and enter the "Time reception On/Off setting" or exit the setting mode by pressing the MIN/MAX key. In area where reception of the WWVB time is not possible, the time reception function can be turned OFF. Use the + key or CH/- key to turn OFF the time reception function. Confirm with the SET key and enter the "12/24-Hour Display setting" or exit the setting mode by pressing the MIN/MAX key. Note: If the Time Reception function is turned OFF manually, the clock will not attempt any reception of the WWVB time as long as the Time Reception OFF function is activated. After setting time reception ON/OFF, press the SET key, "12 h" or "24 h" flashes in the LCD. (default 12 h) Press the + key or CH/- to select the "12 h" or "24 h" display mode. Press the SET again to confirm and to enter the "Manual Time setting" or exit the setting mode by pressing the MIN/MAX key. MANUAL TIME SETTING In case the Temperature Station is not able to detect the Atomic time (WWVB) signal (disturbances, transmitting distance, etc. Use the + key or CH/- key to adjust the hours and then press SET key to go to the minute setting. Press the + key or CH/- key to just the minutes. Confirm with the SET key and enter the "Calendar Setting" or exit the setting mode by pressing the MIN/MAX key Of the year 2006 after initial set-up. Once the radio-controlled time signals are received, the date is automatically updated. However, if the signals are not received, the date can also be set manually. Using the + key or CH/- key, set the year required. Press the SET key to enter the month setting mode. Press the + key or CH/- key to set the month and then press the SET key to go to the day setting. [. . . ] All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which is not in need or repair, you will be charged for the repairs or examination. [. . . ]