User manual LA CROSS TECHNOLOGY WT-5120

[. . . ] WT-5120 433 MHz Radio Controlled Projection Alarm Instruction Manual TABLE OF CONTENTS Topic Inventory of Contents/ Additional Equipment About WWVB Quick Set-Up Guide Detailed Set-Up Guide Battery Installation Program Mode Programming Sequence Function Buttons Manual Time Setting Time Zone Setting Daylight Saving Time (DST) Setting Features & Operations Features Radio-Controlled Time Projection EL Backlight Indoor Temperature Indoor Humidity Remote Temperature Time Alarm Changing Display Mode Mounting Maintenance & Care Troubleshooting Specifications Warranty and Contact Information Page 3 3 4 5 6 6 6 6-7 7 8 8 8 9 9 9 9 10 10 11 11 12 13 14-15 2 INVENTORY OF CONTENTS 1) WT-5120 Alarm Clock 2) TX6U Remote temperature sensor 3) AC adapter/transformer 4) Instruction manual and warranty card. ADDITIONAL EQUIPMENT (not included) 1) Two fresh 1. 5V AA batteries (optional for projection alarm clock) 2) Two fresh 1. 5V AA batteries (for remote temperature sensor) FEATURES OF PROJECTION ALARM Operation of these features is in section III 1. Radio-controlled time Projection of time and/or remote temperature EL backlight Display of indoor temperature/humidity or alarm time Indoor temperature and humidity Remote outdoor temperature Time alarm ABOUT WWVB (Radio Controlled Time) The NIST (National Institute of Standards and Technology--Time and Frequency Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact time signal continuously throughout the United States at 60 kHz. [. . . ] Collins, Colorado, and transmits the exact time signal continuously throughout the United States at 60 kHz. The signal can be received up to 2, 000 miles away through the internal antenna in the projection alarm. Due to the nature of the Earth's Ionosphere, reception is very limited during daylight hours. The projection alarm will search for a signal every night when reception is best. The WWVB radio station receives the time data from the NIST Atomic clock in Boulder, Colorado. A team of atomic physicists is continually measuring every second, of every day, to an accuracy of ten billionths of a second per day. These physicists have created an international standard, measuring a second as 9, 192, 631, 770 vibrations of a Cesium-133 atom in a vacuum. For more detail, visit http://www. boulder. nist. gov/timefreq. htm. To listen to the NIST time, call (303) 499-7111. This number will connect you to an automated time, announced at the top of the minute in "Coordinated Universal Time", which is also known as Greenwich Mean Time (GMT). This time does not follow Daylight Saving Time changes. After the top of the minute, a tone will sound for every second. It is possible that your projection alarm may not be exactly on the second due to the variance in the quartz. However, the clock will adjust the quartz timing over the course of several days to be very accurate; under 0. 10 seconds per day. PROJECTION OF TIME AND REMOTE TEMPERATURE 1. When plugged into an AC outlet, the projection alarm will continuously project the time and remote temperature. When operating on batteries alone, the projection alarm will only project when the snooze button is pressed or the alarm is sounding. The projection will auto-focus for display from three to six feet away. A dark surrounding will be necessary to clearly see the projection. The projection alarm will automatically toggle between the time and outdoor temperature when projecting; either when the "SNOOZE" button is pressed or continuously when using the AC adaptor. The direction of the display can also be rotated 360° in 90° increments by pressing the directional button. Concrete and metal structures offer the most resistance. [. . . ] La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. [. . . ]