User manual LA CROSSE TECHNOLOGY EH-23G RECESSED BUTTONS, BEVELED FACE, ROMAN NUMERALS

[. . . ] Now this precise signal can be received by the atomic watch technology. Your atomic watch receives the WWVB time signal via its built-in antenna system. The proper function of the receiver contained in this product has been tested as a prototype with regard to its sensitivity and range of reception in different places throughout the United States. Any claim for warranty ­ express or implied ­ due to the watch's failure to properly receive the radio signal due to interference, whatever may be the source of this interference, are hereby expressly excluded in all respects. [. . . ] Please take note of the AM/PM symbols in the digital display. The proper date will be calculated by the internal microprocessor and at the end of the adjustment the display returns to the default mode showing the date. 8. Trouble Shooting Problem Solution The battery must be replaced as soon as possible (see 5. Replacing the Battery. ) Depress the T1 button and place your watch in a *free field position for at least 10 minutes, preferably at night when reception is best. Press the T1 button for at least 3 seconds after reentering the reception range. Depress the T1 button and place your watch in a *free field position for at least 10 minutes, preferably at night when reception is best. Press T1 and T2 together for more than 3 seconds then reposition the hands as described under 5. Replacing the battery. Symptom 5. Replacing the Battery A low battery is signaled by a blinking "LO" in the digital display. The battery should be replaced by trained personnel to avoid damage and to maintain the water resistance according to factory specifications. After battery replacement the hands of your atomic watch must be repositioned to 12 o'clock. The hands can be advanced either incrementally by repeatedly pressing the T2 button or rapidly by holding the T2 button. Pressing the T2 button briefly advances the minutes, holding the button down lets the minute hand move continuously until the T2 button is released. (The minute is also shown in the LCD helping you to set the correct time. ) Your watch now uses its integrated quartz movement. Please note in this mode your watch cannot display the date. The time you have set is retained until your watch is able to receive the signal from the WWVB transmitter again. The date will then also be set and displayed in the LCD again. After your atomic watch automatically receives the WWVB signal the watch will be set to Pacific standard time. You must then either press the T1 button to confirm the time or set the desired time zone as described in 4. Setting the Time Zone. 1) The letters "LO" blink in the digital display. The battery is running low. 2) Your watch does not automatically change between daylight saving time and standard time. The watch has not received the WWVB time signal. You may be out of reception range. 6. Technical Data Reception Frequency Quartz Time Base Battery Type Operating range voltage Battery Life Operating Temperature 60 kHz 32 kHz CR 1620 2. 4V to 3. 4V approx. 2 years 32 ºF to 122 ºF (0 ºC to 50 ºC) You may be in or near a disturbance field such as a metal structure, appliances or particularly climactic conditions. 7. Water Resistance · The "water-resistant" state only applies in new condition. · External influences may affect water resistance. · Please have your watch checked regularly. 3) The hands do not move and the digital display is blank. The battery may be empty. 4) The watch hands do not advance exactly to 12 o'clock during manual time signal reception. The watch hands are not properly positioned. * no designation *Free field position means a place free of radio disturbances such as electrical appliances, metal structures and particular climactic conditions. WARRANTY INFORMATION La Crosse Technology, Ltd provides a 10-year limited warranty on the movement of this product against manufacturing defects in materials and workmanship. All other components of the watch including the lens and strap are warranted for 1-year against manufacturing defects in materials and workmanship. [. . . ] You may also have other rights specific to your State. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information contact: La Crosse Technology, Ltd 2809 Losey Blvd S. La Crosse, WI 54601 Phone: 608. 782. 1610 Fax: 608. 796. 1020 e-mail: support@lacrossetechnology. com (warranty work) sales@lacrossetechnology. com (information on other products) web: www. lacrossetechnology. com All rights reserved. [. . . ]