User manual LA CROSSE TECHNOLOGY TX2000 DISCOVERY

[. . . ] CONTENTS Topic Inventory of Contents About WWVB Quick Set-Up Guide Detailed Set-Up Guide Battery installation Program Mode Program Sequence Function Keys Setting the LCD Contrast Time Zone Setting Daylight Saving Time Setting Radio-Controlled Time Setting 12/24 Hour Time Setting Time Setting (WWVB & Manual) Setting the Year, Day and Month Setting the Snooze Setting the Temperature Format Features Indoor Temperature Outdoor Temperature Minimum & Maximum Records (Indoor, Outdoor, & Resetting) Alarm (Setting, Snoozing & Stopping) Viewing date, weekday or alarm time Additional Remote Control Sending Units (Set-Up, Viewing, & Operation) Mounting Troubleshooting Maintenance & Care Specifications Warranty Information Page INVENTORY OF CONTENTS 1. One TX6U remote temperature sensor with mounting bracket (Figure 2). Three each, ½" Philips screws. One, Philips screwdriver. Figure 1 Figure 2 ABOUT WWVB (Radio Controlled Time) The NIST (National Institute of Standards and Technology--Time and Frequency Division) WWVB radio station is located in Ft. [. . . ] "MAX" appears above the outdoor temperature and the LCD will flash, indicating that the maximum temperature and the time and date of occurrence are displayed. 2. 3. While "MAX" is still displayed press the OUT button again to return to the current data display. Or you can wait 30 seconds, during either the minimum or the maximum readings, and the unit will automatically return to current data readings. 14 C. RESETTING THE MIMIMUM AND MAXIMUM RECORDS 1. All the Indoor records (minimum and maximum) will be reset after the IN button is pressed and held for 5 seconds. All the Outdoor records (minimum and maximum) will be reset after the OUT button is pressed and held for 5 seconds. IV. SETTING THE ALARM (alarms 1 and 2) Note: There are two alarms that can set. Each alarm will sound for a complete duration of 2 minutes. Press and hold the AL1 button for 5 seconds, or until the alarm-time display flashes in the DATE LCD. 2. 5. 6. 7. Press the IN button to set the alarm hours, and the OUT button to set the alarm minutes. Press the AL1 button, or wait 15 seconds for the unit to automatically confirm the alarm time and return to display the date in the DATE LCD as normal. The ((1)) icon, appearing in the DATE LCD, indicates that the alarm is set to sound at the programmed time. Programming the alarm time automatically activates the alarm to sound at the programmed time. To deactivate the alarm, press the AL1 button (removing the ((1)) icon from the screen). To reactivate the alarm, press the AL1 button again. After each activation or deactivation, the programmed alarm time is displayed. Wait 15 seconds and the date will display in the DATE LCD again. To set, activate, and deactivate alarm 2, follow the directions above for alarm 1--using the AL2 button instead of the AL1 15 button. The ((2)) icon will represent activation and deactivation of Alarm 2. Press and release the SNZ button to activate the snooze function. To turn the alarm off completely press any button other than the SNZ button. The snooze function will last for the length it was set for in the set-up mode before the alarm begins to sound again. Either the ((1)) or the ((2)) icon will flash during the snooze mode depending on which of the alarms is in the snooze mode. V. VIEWING DATE, WEEKDAY OR TIME ALARM The date display section can be set to view the date, weekday, time alarm ((1)) and ((2)). [. . . ] Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. [. . . ]