User manual LA CROSSE TECHNOLOGY WS-1913TWC-IT

[. . . ] The transmitter reception icon is now blinking again to indicate that the station is trying to get the rain sensor data. It will stop blinking once the rain sensor has been detected. If this does not happen after 135 seconds, you will need to start again from step 2. You may need to check the cable for correct connection and all the components for correct function by manually turning the wind-gauge by moving the wind-vane; tilting the rain sensor to hear the impact of the internal moving seesaw, etc. [. . . ] If still not successful, the reception is tried for 45 seconds on 910MHz. This will also be done for re-synchronization. Note: When changing batteries in any of the units, all units need to be reset by following the setup procedures. This is because a random security code is assigned by the transmitter and rain sensor (optional) at start-up and this code must be received and stored by the Weather Station in the first 90 seconds of power being supplied to it. Note: The stored History record will not be kept after the battery change is done on the weather station. The LCD screen is split into 3 sections displaying the following information: 1. Time and date/ indoor temp/ second Wind data, outdoor temperature and humidity, dew point, weather forecast icon and tendency indicator Air pressure history, relative air pressure, rainfall data (optional) Calendar / indoor temperature / seconds display Wind speed / gust* in mph, km/h, m/s Weather forecast Icon Low battery indicator (weather station) Outdoor relative humidity in % Low battery indicator # (transmitter) Relative air pressure / 24 hr rainfall / Total rainfall display* (only if there is a rain sensor being used) SET key + key HISTORY key MIN/MAX key SET key x Press and hold to enter manual setting modes: LCD contrast, Manual time setting, 12/24 hour time display, Calendar setting, ºC/ ºF temperature unit, Wind speed unit, Rainfall unit, Pressure unit, Relative pressure reference setting, Weather tendency threshold setting x Press to toggle between the display of Mode 1 or Mode 2: Mode1: "Wind speed + outdoor temp + rel. Pressure" Mode 2: "Gust + Dew Point temp + rainfall data (only if there is a rain sensoroptional)" (Mode 2 displayed will be shown for 30 seconds. Then it will return to normal display x Press to activate the reset mode when MAX or MIN record is shown + key In display Mode 1, press to toggle the date, weekday, + date, Indoor temp, or sec In display Mode 2, press to toggle the Relative Pressure, 24 hour rainfall and Total rainfall (if there is a rain sensor- optional). Press to adjust (increase) the level of different settings Press to confirm to reset the MIN/MAX record HISTORY key x Press to display the weather data history records or exit manual setting mode MIN/MAX key x Press to display MIN/MAX records of various weather data or adjust (decrease) the level of different settings When the signal from the transmitter/ or Rain sensor (optional) is successfully received by icon will not the Weather Station, the icon will be switched on. (If not successful , the be shown on the LCD). User can therefore easily see whether the last reception was successful ("ON" icon) or not ("OFF" icon). On the other hand, the short blinking of icon shows that a reception is being done at that time. The * In normal display user may press the SET key shortly to toggle between Mode1 and Mode 2 display: Mode 1: Wind speed, outdoor temperature, relative air pressure are shown. Using 915MHz wireless transmission gives users little restriction on placement because all units can be positioned virtually anywhere within a 330 ft / 100 meters radius of the base station. Please ensure that the cable included in this set meets your distance requirements (see accessories in the main user manual for adding extension cables). Important: Ensure all signals can be received and/or all cable distances meet with your requirements at the point of fixing particularly before you start drilling any mounting holes. Secure the main unit to the shaft of the mast holder using the single screw provided with the front of the sensor (marked E) facing in the East-West direction otherwise wind direction will not be accurate. Now fix the entire unit to a suitable mast using the U-bolt, washers and nuts found in this set. Note: For best results mount the wind sensor onto a mast to allow the wind to freely travel from all directions to enable an accurate reading (ideal mast size should be from Ø 5/8" to 11/4"). Transmitter signal reception icon In Mode 1, this reception icon is showing the condition of the reception of the signal from Thermo-hygro transmitter To wall mount the thermo-hygro sensor, fix the wall holder onto the desired wall (2 screws are supplied), plug the sensor firmly into the wall holder and then carefully replace the rain cover back over the thermo-hygro sensor. Note: After mounting the units, should the weather data not be received, user may need to remove the batteries from all units and redo the set-up procedures after about 5 minutes. [. . . ] This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. [. . . ]