User manual LA CROSSE TECHNOLOGY WS-3510

[. . . ] TOUCH-SCREEN WEATHER STATION MODEL WS-3510 QUICK OPERATION GUIDE 1 Shipping Contents The shipping contents of the touch-screen weather station WS3510 include the touch-screen weather station, a remote temperature/humidity sensor, the respective connecting cables, an AC adapter and the PC software package on CD-ROM. 2 Connections The use of the direct cable connection between the touch-screen weather station and remote temperature/humidity sensor depends on the chosen operating mode (see Item 3 Power Supply). 3 Power Supply Depending on the type of data transmission from remote temperature/humidity sensor to touch-screen weather station, the units can be supplied with power in the following possible combinations: · With cable connection or 433 MHz wireless transmission: touchscreen weather station batteries, remote temperature/humidity sensor batteries. · With 433 MHz wireless transmission: touch-screen weather station AC adapter, remote temperature/humidity sensor batteries. · With cable connection: Both units supplied by AC adapter. [. . . ] after a battery change in the remote temperature/humidity sensor) without the necessity of a comprehensive re-setup of all system components Acknowledge with CONFIRM. 7 Default Settings (Factory Reset) Allows a reset of all weather data from the non-volatile buffer memory (EEPROM) and reset of all set and/or stored values to the factory settings set prior to shipment Acknowledge with CONFIRM. Note: It will take about 5 minutes for the factory reset process. During this period, the text "Factory Reset In Progress" will be shown. After the reset process is finished, the LCD will switch off and the text "Remove Battery" will be displayed. Remove the battery and perform system start again. See "3 - Putting in Operation" paragraph. Leave the basic settings procedure (Setup Mode) with EXIT. 5 Display of stored Min/Max Values and Alarm Value Settings The selected values are simultaneously displayed and flashing in their respective display sections when showing the coinciding min/max value. To recall the measuring and alarm values the menu shown below will have to be activated by touching the touch-screen in the center of the text display section (last two lines at the bottom of the LCD). The display of the values is started by touching the displays MINMAX or ALARMS. When MINMAX is selected the below shown menu step is activated, which in turn leads to the displays of the stored Min/Max values by use of MIN / MAX field. Note: During individual display of the stored Min/Max values the top line of the LCD screen will automatically display the time and date of the record. The following menu item will appear upon touching the display ALARMS. By selecting *LO AL* or *HI AL* the unit will display the set low and high alarm values. These values can be directly selected individually. 8 Because of the constant access to the opposite menu items, MINMAX and ALARMS, it is possible at any time to toggle between the MIN/MAX and ALARMS value displays. Any action can immediately be terminated through EXIT. 6 Radio-controlled WWVB Clock The radio-controlled WWVB clock is controlled by the radio signal of the WWVB time code sensor and will thus set time and date automatically. Under bad reception conditions however both can be set manually as follows: Setting the Time The action is started by touching the time display in the TIME section of the touch-screen. Select TIME in the menu section (last two lines on the LCD). Set the hours and minutes. Leave the mode with EXIT or wait for automatic time-out. Setting the Date The action is started by touching the date display in the DATE section of the touch-screen. Set the year, month and date and day. Leave the mode with EXIT. Note: By twice touching the DATE section the display will toggle between the following: · Date in DD. MM. YY format (24-hour time format) or Date in MM. DD. YY format (12-hour time format) · Weekday, Date of month, Month (24-hour format) or Weekday, Month, Date of month (12-hour time format) · Seconds · Set wake-up alarm time Setting the Wake-up Alarm The action is started by touching the time display in the TIME section. 9 Press ALARM in the menu section (last two lines on the LCD). Set hours and minutes of the wake-up time. Leave the mode with EXIT. Note: · The wake-up alarm is activated/deactivated by twice touching the TIME section. Here the alarm symbol (((·))) will show or disappear after EXIT (or automatic time-out). [. . . ] La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. [. . . ]