User manual LA CROSSE TECHNOLOGY WS-3610U-CH

[. . . ] Touch Screen Weather Center Model WS-3610 QUICK SET UP GUIDE 1 Shipping Contents The shipping contents of the WS-3610 Touch Screen Weather Center include a Base Station (Receiver), a Thermo-Hygro Sensor (433 MHz Transmitter), a Rain Sensor and a Wind Sensor, the respective Connecting Cables, an AC Adapter and a CDROM with a Package of PC Software for collected Weather Data. 2 Connections Connect the Rain Sensor and Wind sensor cables to their respectively marked jacks in the Thermo-Hygro sensor BEFORE powering up the Base Station or the ThermoHygro Sensor. The Thermo-Hygro Sensor and Base Station can be directly connected via cable if the wireless 433 MHz radio transmission is not desired, and data transmission free of localized radio interference is an important factor. (The use of the direct cable connection between the Base Station and Thermo-Hygro Sensor depends on the finally chosen operating mode (see Item 3 Power Supply). [. . . ] Operation and settings of the Rain function are essentially identical to the ones described in Item 9 above. Therefore a short description of the minor differences in regards to Item 9 will be a sufficient enough explanation. · Since it is not necessary to display minimum rain values, the menu does not offer the item MIN but MAX only to display the various maximum rain amounts. Since no minimum rain values are stored, upon activating the ALARM, the display will immediately proceed to the high alarm setting as described in section 9 above. · 18 Note: The alarm option is only offered during display of the last hour and last 24-hour rainfall amounts. No exact definition of alarm time is possible for weekly and monthly rain amounts; therefore these alarm functions have been omitted. · When touching the TOTAL field in the RAIN section, the total rain amount accumulated since the last deletion is displayed. This can be erased by touching RAIN TOTAL in the bottom section of the LCD, followed by CONFIRM. Additional Information regarding the Outdoor Temperature Display (Outdoor Temp) 11 Note: Touch the OUTDOOR field to toggle the display between the following: · Outdoor Temperature (Outdoor Temp) · Wind Chill · Dew Point All setting and display options only pertain to the presently displayed value. 12 Additional Information regarding the Wind Display Note: Touch the WIND field to toggle the display between the following: · Wind Speed · Wind Direction (Abbreviations of the compass rose descriptions) · Wind Direction (Degrees) · Wind Gust All setting and display options only pertain to the presently displayed value. 19 12. 1 Operating and Setting the Wind Direction Alarm In the Wind Direction display, the display of minimum or maximum values is unnecessary. However it is possible to set wind direction alarms. Call up the corresponding menu in the bottom section of the LCD by touching the center of the WIND field. Proceed by touching DIR AL. In the following menu up to 16 separate alarms can be set clockwise around the compass rose from N through NNW in steps of 22. 5°. (0° through 337. 5°) Here the wind direction can be selected by touching UP or DOWN and switched ON or OFF with (Wind Direction) by touching ON/OFF in the upper left part of the menu display. The wind alarm feature can be enabled, or completely deactivated by touching the ON and OFF fields in the menu shown below. Touch EXIT to return to normal display. 20 13 Operating and Setting the EL Backlight (light), Buzzer (sound), and Alarm history (fields in the WIND Section) 13. 1 EL Backlight (Light) For enhanced readability of the LCD the EL backlight can be switched ON or OFF by touching the LIGHT field once. When the backlight is switched to "Enabled", it will glow for approximately 20 seconds every time any of the LCD sections is touched. The switching condition (Enabled/Disabled) is shown in the bottom section of the LCD for about 20 seconds. Note: In case that the Base Station is battery operated, repeated use of the EL backlight will result in a considerable decrease of the life of the batteries. It is recommended either to operate the Base Station with the included AC adapter, or deactivate the EL backlight (see above). 13. 2 Buzzer The keypad beep and the audible alarms of the Base Station can be switched ON or OFF by touching the BUZZER section. The switching condition ON or OFF is displayed directly in the BUZZER section as well as in the bottom section of the LCD for about 20 seconds (Enabled/Disabled). 13. 3 Alarm Upon touching the ALARM field in the WIND section, all set and activated alarms (except time alarm) will be shown numbered and sorted according to time of appearance, along with NEXT and EXIT. For each alarm preset, the time and date can be displayed by touching the center of the bottom section of the LCD. 21 14 PC Connection In addition to the LCD monitor, the WS-3610 has the ability to transfer all collected time and weather data to a PC via a Com port connection. The supplied PC software provides complete sets of history data, data graphing, and webpage update capabilities. [. . . ] Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. [. . . ]