User manual LA CROSSE TECHNOLOGY WS-8056U

[. . . ] WS-8056U 433 MHz Radio Controlled Temperature Alarm Instruction Manual TABLE OF CONTENTS Topic Inventory of Contents/ Additional Equipment About WWVB Quick Set-Up Guide Detailed Set-Up Guide Battery Installation Program Mode Function Buttons Time Zone Setting DST (Daylight Saving Time) Setting Language Selection Time Setting Calendar Setting 12/24-Hour Setting Selecting °F or °C Features & Operations Changing Display Mode (viewing seconds) The Alarm Indoor temperature Remote Temperature Mounting Maintenance & Care Troubleshooting Specifications Warranty Information Page 3 3 4 5 6 6 7 7 7 8 8 8 9 10 11 11 11 12 13 14 15-16 2 INVENTORY OF CONTENTS 1) WS-8056U 2) TX6U remote temperature transmitter 3) Instruction manual and warranty card. ADDITIONAL EQUIPMENT (not included) 1) 2) 3) 4) Two fresh 1. 5V AA batteries. Appropriate screwdriver for screws. ABOUT WWVB (Radio Controlled Time) The NIST (National Institute of Standards and Technology--Time and Frequency Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact time signal continuously throughout the United States at 60 kHz. [. . . ] 1) Hold down the "SET" button for 2 seconds (the selected time zone will flash), press and release the "SET" button 3 more times until the hour "12" flashes in the time LCD. 2) Press and release the "+" button to select the hour. Note: when setting the hour, "PM" will appear to the left of the hour display, if it is AM nothing will be displayed. 3) Press and release the "SET" button to confirm the hour setting, and to shift to select the minutes. 4) Press and release the "+" button to select the minutes. 5) Press and release the "SET" button to confirm the time setting, and to advance to manually set the calendar. 7 F) CALENDAR SETTING Note: When the WWVB signal is found, that date will over-ride the manually set date. 1) Hold down the "SET" button for 2 seconds (the selected time zone will flash), press and release the "SET" button 5 more times until the default year "00" flashes in the date LCD. 2) Press and release the "+" button to select the year. 3) Press and release the "SET" button to confirm the year and to move to select the month. 4) The default month "1" will flash. Press and release the "+" button to select the appropriate month. 5) Press and release the "SET" button to confirm the month and to move to select the date. 6) The default date "1" will flash. Press and release the "+" button to select the appropriate date. 7) Press and release the "SET" button to confirm the date and to move to select the weekday. 8) The default weekday "MON" (depends on selected language) will flash. Press and release the "+" button to select the appropriate weekday. 9) Press and release the "SET" button to confirm the calendar settings and to advance to select either 12 or 24-hour time display. G) 12/24-HOUR SETTING 1) Hold down the "SET" button for 2 seconds (the selected time zone will flash), press and release the "SET" button 9 more times until the "12" hour time display flashes in the time LCD. 2) Press and release the "+" button to toggle between 12 and 24 hour time. 3) Press and release the "SET" button to confirm the 12/24-hour time display and to advance to select either °F or °C. H) SELECTING °F OR °C 1) Hold down the "SET" button for 2 seconds (the selected time zone will flash), press and release the "SET" button 10 more times until the default "°F" flashes in the time LCD. [. . . ] 4) Remove batteries for five minutes, reinsert and leave the unit alone overnight without pressing buttons. 5) If problems persist contact La Crosse Technology. Hour is incorrect (minute and date are correct). Problem: 1) Be sure correct time zone and daylight saving time are Solution: selected. [. . . ]