User manual LA CROSSE TECHNOLOGY WS-9009B-IT

[. . . ] THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do not allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. in/out key: min/max key: Press to toggle the indoor and outdoor temperatures (see View 1and 2 below). [. . . ] Once the batteries are in place, all segments of the LCD will light up briefly. Following the indoor temperature will be displayed. If the indoor temperature is not shown in the LCD after 60 seconds, remove the batteries and wait for at least 60 seconds before reinserting them. Once the indoor data is displayed you may proceed to the next step. After the batteries are inserted, the Temperature Station will start receiving outdoor temp data from the transmitter. The outdoor temperature should then be displayed on the Temperature station. If this does not happen after 2 minutes, remove the batteries from both units and start again from step 1. In order to ensure sufficient 915 MHz transmission, the outdoor transmitter should be placed a distance of no more than 260 feet (80 meters) from the Temperature Station and the transmitter (see notes on "Positioning"). Clip the remote temperature transmitter onto the bracket. Note: The mounting surface can affect the transmission range. If, for instance, the unit is attached to a piece of metal, it may then either reduce or increase the transmitting range. For this reason, we recommend not to place the unit on any metal surfaces or in any position where a large metal or highly polished surface is in the immediate vicinity (garage doors, double glazing, etc. ). Before securing in place, please ensure that the Temperature Station can receive the 915MHz signal from the temperature transmitter at the positions that you wish to place them. WARRANTY La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd's authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the 3. 4. los valores de temperatura mínimos. Presione nuevamente para ver los valores de temperatura máximos). TECLAS DE FUNCIÓN La estación de temperatura sólo tiene dos teclas de función fáciles de usar: Tecla interior/exterior Tecla mín/máx Esta garantía limitada comienza en la fecha original de compra y es válida sólo para productos comprados y usados en América del Norte, y sólo para el comprador original del producto. Para recibir el servicio de garantía, el comprador debe ponerse en contacto con La Crosse Technology Ltd a fin de realizar una determinación del problema y los procedimientos de servicios. Sólo se puede realizar servicio de garantía en un centro de servicio autorizado por La Crosse Technology Ltd. Se debe presentar el recibo de venta con fecha original, según se solicite, como comprobante de compra a La Crosse Technology Ltd o el centro de servicio autorizado por La Crosse Technology Ltd. La Crosse Technology Ltd reparará o reemplazará este producto, a su discreción y sin cargo según se establece en el presente, con piezas o productos reacondicionados si presenta defectos durante el período de garantía limitada especificado anteriormente. [. . . ] Entonces se debe mostrar la temperatura exterior en la estación de temperatura. Si esto no ocurre luego de 2 minutos, retire las baterías de ambas unidades y comience nuevamente desde el paso 1. Para garantizar una transmisión de 915 MHz suficiente, se debe colocar el transmisor exterior a una distancia no mayor que 80 metros (260 pies) desde la estación de temperatura y el transmisor (consulte las notas sobre "Colocación"). Presione para ver Para montaje en pared: Fije la abrazadera en la pared deseada con los tornillos y anclas de expansión de plástico. [. . . ]