User manual LA CROSSE TECHNOLOGY WS2800

[. . . ] WS-2800 Wireless Professional Weather Center Instructions Manual TABLE OF CONTENTS TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INVENTORY OF CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FEATURES:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Note: If a storm warning alarm is activated, the downward weather tendency arrow will be flashing. WIND DIRECTION DISPLAY TYPE SETTING The wind direction can be displayed using either compass directions or degree measurements (default setting is compass directions). 17 1. Press the UP ARROW key or DOWN ARROW key to toggle from compass directions to degree measurements. If you do not wish to reset the display to factory defaults, simply press the ALARM or MIN/MAX key, or wait until the SET mode times out and returns to the normal display mode. If you wish to perform a FACTORY RESET, press the SET key to confirm and to enter the FACTORY RESET PROCEDURE. SEE WARNINGS in the FACTORY RESET section. FACTORY RESET PROCEDURE WARNING: Performing a factory reset will erase all MIN/MAX values and weather data stored in the display's internal memory and return the weather units settings back to the factory defaults. If you have not yet uploaded the data to the Heavy Weather Pro software, the data will be lost. If you do not wish to reset the display to factory defaults either: · press the MIN/MAX key or the ALARM key, or · simply wait until the SET mode times out and returns to the Mode 1 display (normal mode). To reset the display to factory defaults, follow the procedure below: WARNING: A factory reset will erase the connection between the display and the thermohygro sensor and require the connection to be re-established. 1. "rES oFF" will start flashing. Use the UP ARROW key to turn "rES on". Press the SET key to confirm and a countdown timer will begin counting down from "127" When the timer displays "dOnE", you must remove the batteries from the display for 10 minutes. While the batteries are out of the display, also remove the batteries from the thermo-hygro sensor. After waiting for 10 minutes, insert the batteries into the thermo-hygro sensor, making sure to align the "+" symbol on the batteries with the markings on the battery cover and inside the battery compartment. 18 5. Within 2 minutes of inserting the batteries into the thermo-hygro sensor, insert the batteries into the display, making sure to align the "+" symbol on the batteries with the markings inside the battery compartment. Wait 5 minutes for the outdoor weather data to display. If any of the outdoor data displays "--" after waiting for 5 minutes, follow the "Setting Up" Procedure near the beginning of this manual or in the Quick Set Up Manual included with the product. TO EXIT THE MANUAL SETTING MODE To exit the manual setting anytime during the manual setting modes, either: · Press the ALARM key or the MIN/MAX key or · Simply wait 30 seconds until the SET mode time out and return to the Mode 1 display (normal mode). WEATHER ALARM OPERATIONS The Weather alarms can be set when certain weather conditions are met according to your requirements. For example, you can set the thresholds for the outdoor temperature C C to +40° (high) and -10° (low), while enabling the high alarm and disabling the low alarm (i. e. temperatures <-10° won't trigger alarm, but temperatures >+40° will). [. . . ] Replace only with new batteries of the recommended type. · When cleaning the display and casings, use a soft damp cloth only. Do not use solvents or scouring agents as they may mark the LCD and casings. · Do not submerge the unit in water. [. . . ]