User manual LA CROSSE TECHNOLOGY WS2801

[. . . ] WS-2801-IT Wireless Professional Weather Center Instructions Manual TABLE OF CONTENTS INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 INVENTORY OF CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 FEATURES:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 WIRELESS DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To reset the display to factory defaults, follow the procedure below: WARNING: A factory reset will erase the connection between the display and the thermohygro sensor and require the connection to be re-established. "rES oFF" will start flashing. Use the UP ARROW key to turn "rES on". Press the SET key to confirm and a countdown timer will begin counting down from "127". When the timer displays "dOnE", you must remove the batteries from the display for 10 minutes. While the batteries are out of the display, also remove the batteries from the thermo-hygro sensor. After waiting for 10 minutes, insert the batteries into the thermo-hygro sensor, making sure to align the "+" symbol on the batteries with the markings on the battery cover and inside the battery compartment. 48 5. Within 2 minutes of inserting the batteries into the thermo-hygro sensor, insert the batteries into the display, making sure to align the "+" symbol on the batteries with the markings inside the battery compartment. Wait 5 minutes for the outdoor weather data to display. If any of the outdoor data displays "--" after waiting for 5 minutes, follow the "Setting Up" Procedure near the beginning of this manual or in the Quick Set Up Manual included with the product. TO EXIT THE MANUAL SETTING MODE To exit the manual setting anytime during the manual setting modes, either: · Press the ALARM key or the MIN/MAX key or · Simply wait 30 seconds until the SET mode time out and return to the Mode 1 display (normal mode). WEATHER ALARM OPERATIONS The Weather alarms can be set when certain weather conditions are met according to your requirements. For example, you can set the thresholds for the outdoor temperature to +40°C (high) and -10°C (low), while enabling the high alarm and disabling the low alarm (i. e. temperatures <-10°C won't trigger alarm, but temperatures >+40°C will). · · · · If the value meets the condition for high alarm or low alarm, the buzzer will ring for 2 minutes and the value will blink, along with the corresponding icon ("HI AL"/ "LO AL"). The high and low alarms can be switched On/Off independently, according to your needs. If at any time during the alarm setting process you would like to exit alarm setting mode, press the MIN/MAX key or wait for about 30 seconds and the display will return to normal display mode automatically. In normal display mode, press the ALARM key to enter ALARM mode. Subsequent presses of the ALARM key will advance to the next weather alarm section. · Note: Weather alarms can also be set from the Heavy Weather Pro software. Consult the Heavy Weather Pro User's Guide for instructions. THE FOLLOWING WEATHER ALARMS CAN BE ADJUSTED IN ALARM SETTING MODE · High and Low pressure alarms · High and Low indoor temperature alarms · High and Low indoor humidity alarms · High and Low outdoor temperature alarms · High and Low outdoor humidity alarms · High wind gust alarm · Wind direction alarm · High rainfall amount in 24 hour period alarm 49 DEFAULT WEATHER ALARM VALUES Pressure Temperature (In or Out) Relative Humidity (In or Out) PRESSURE ALARMS 1. In the normal display mode, press the ALARM key once. [. . . ] The batteries shall be taken out from the unit before the product is to be stored for a long period of time. Immediately remove all low powered batteries to avoid leakage and damage. Replace only with new batteries of the recommended type. When cleaning the display and casings, use a soft damp cloth only. [. . . ]