User manual LA CROSSE TECHNOLOGY WS8300

[. . . ] The outdoor temperature and humidity should then be displayed on the Temperature Station. If this does not happen after 2 minutes, the batteries will need to be removed from both units and the setup restarted from step 1. In order to ensure an optimal 868 MHz transmission, in good conditions, the distance between the Temperature Station and the transmitter should not be no more than 100 meters (see notes on "Positioning" and "868 MHz Reception"). When more than one transmitter is used 1. User shall remove all the batteries from the Temperature Station and the transmitter and wait 60 seconds (if setup has been done with one transmitter before). [. . . ] A random security code is assigned by the transmitter at start-up and this code must be received and stored by the Temperature Station within the first 3 minutes of power supplying. 31 BATTERY CHANGE: It is recommended to replace the batteries in all units at least every 24-month to ensure optimum accuracy of these units. Please participate in the preservation of the environment. Return used batteries to an authorised depot. FUNCTION KEYS: Temperature Station: The Temperature Station has only two function keys, easy to use. MIN/MAX/+ key SET/ CH key Set/ch key (Setting/Channel) · Press and hold for about 3 seconds to enter the Manual setting mode. · Used to toggle between the data of different outdoor transmitters (channel) "1", "2" and "3", when more than 1 transmitter is used. 32 Min/max/+ key (Min/ Max temperature) Used to toggle between the minimum and maximum recorded readings of indoor & outdoor temperature and outdoor humidity. LCD SCREEN AND SETTINGS: Outdoor Temp. in °C Time Outdoor humidity %RH Indoor Temp. in °C Outdoor Reception Signal icon* Transmitter Transmitter Low battery identification (channel No. ) indicator Receiver Low battery indicator *When the signal is successfully received by the Temperature Station, the Outdoor reception icon will be switched on. (If not successful, the icon will not be shown). The user can therefore easily see whether the last reception was successful (icon 33 "ON") or not (icon "OFF"). On the other hand, the flashing of the icon shows that a reception is being done now. For a better legibility, the LCD screen is split into 4 sections, displaying the information for time, indoor temperature, and outdoor data. Section 1 Section 2 Section 3 Section 4 - Outdoor temperature - Outdoor humidity - Time - Indoor temperature MANUAL SETTING: 12 / 24- HOUR TIME DISPLAY SETTING AND TEMPERATURE UNIT (°C/°F) SETTING User may choose to display the time in 12-hour or 24-hour format : Note: When the time display is in 12-hour mode, the temperature unit will be set to °F; when the time mode is in 24-hour, the temperature unit will be set to °C. In normal display mode, press and hold the "set/ ch" key for about 3 second. The "12h" or "24h" digit will be flashing. Press the "min/max/+" key to set the desired time display format. 34 3. Press shortly the "set" key to advance to the MANUAL TIME SETTING. MANUAL TIME SETTING User shall manually set the time of Temperature Station by the following steps: 1. The hour digit of the time display will be flashing. Press the "min/max/+ "key to adjust the hour. Press "set" key to confirm and go to the minute setting. Press the "min/max/+" key to adjust the minute. Press "set" key once more to return to normal display. VIEWING THE MINIMUM AND MAXIMUM READINGS : User may view the minimum and maximum temperature and humidity data records of the indoor or outdoor channels by following these steps : 1. In normal display, press "set/ch" key to choose the desired channel (transmitter). Press the "min/max/+" key once to view the minimum indoor temperature, minimum outdoor temperature and minimum outdoor humidity of the selected channel. 35 Minimum icon Selected channel No. 3. Press the "min/max/+" key once more to view the maximum indoor temperature, maximum outdoor temperature and maximum outdoor humidity of the selected channel. Maximum icon Selected channel No. 36 RESETTING READINGS : THE MINIMUM AND MAXIMUM User may reset the minimum and maximum temperature and humidity data to the current value by following this step : 1. Press and hold the "min/max/+" key for about 3 seconds to reset all the minimum/ maximum data of all channels and the indoor sensor to the current values in a single action. THERMO-HYGRO TRANSMITTER : The outdoor temperature and humidity are measured and transmitted every 4. 5 seconds. [. . . ] User shall take an active part in the reuse, recycling and recovery of the electrical and electronic waste. The unrestricted disposal of electronic waste may do harm on public health and the quality of environment. As stated on the gift box and labeled on the product, reading the "User manual" is highly recommended for the benefit of the user. This product must however not be thrown in general rubbish collection points. [. . . ]