User manual LA CROSSE TECHNOLOGY WS9024

[. . . ] There is no need to reset the units, should the probe be 43 unplugged or re-plugged again. The Temperature Station will automatically detect the temperature probe data and will display the temperature data on Channel 2 after the probe is plugged. SETTING UP: When one transmitter is used: 1. First, insert the batteries into the transmitter (see "How to install and replace batteries in the Temperature transmitter" below). Within 2 minutes of powering up the transmitter, insert the batteries to the Temperature Station (see "How to install and replace batteries in the Temperature Station" below). [. . . ] To install and replace the batteries, please follow the steps below: 1. Insert batteries observing the correct polarity (see marking). Replace compartment cover. 48 HOW TO INSTALL AND REPLACE TEMPERATURE TRANSMITTER BATTERIES IN THE The Temperature transmitter uses 2 x AAA, IEC LR3, 1. 5V batteries. When batteries will need to be replaced, the low battery icon will appear on the LCD of the Temperature Station. To install and replace the batteries, please follow the steps below: 1. Remove the battery compartment cover at the back of the transmitter. Insert the batteries, observing the correct polarity (see marking). Replace the battery cover on the unit. 49 Note: In the event of changing batteries in any of the units, all units need to be reset by following the setup procedures. This is because a random security code is assigned by the transmitter at start-up and this code must be received and stored by the Temperature Station in the first few minutes of power supplying. BATTERY CHANGE: It is recommended to replace the batteries in all units every 24 months to ensure optimum accuracy of these units. Please participate in the preservation of the environment. Return used batteries to an authorized depot. 50 FUNCTION KEYS: Temperature Station: The Temperature Station has only two easy to use function keys. Set/ ch key min/ max/ + key Set/ch key (Setting/Channel) · Press and hold for about 3 seconds to enter the Manual setting mode. · Press shortly to toggle between different channel readings. 51 min/max/+ key (Min/ Max temperature) · Used to toggle between the minimum and maximum recorded readings of indoor & outdoor temperature and indoor humidity. · Press and hold to reset minimum and maximum record (when min or max record is shown). 52 LCD SCREEN AND SETTINGS: Time Indoor Humidity %RH Indoor Temperature in °C Outdoor Temperature in °C Channel No. Outdoor Reception Signal icon* Receiver Low battery indicator 53 Transmitter Low battery indicator * When the signal from the transmitter is successfully received by the Temperature Station, this icon will be switched on. (If not successful, the icon will not be shown on the LCD). User can therefore easily see whether the last reception was successful ("ON" icon) or not ("OFF" icon). On the other hand, the short blinking of the icon shows that a reception is being done at that time. For a better display clarity, the LCD screen is split into 3 sections, showing the information of time, indoor temperature and humidity, and outdoor data. · Section 1 - TIME Display of time. Section 2 - INDOOR TEMPERATURE AND HUMIDITY · Display of indoor temperature and humidity. 54 Section 3 - OUTDOOR TEMPERATURE · Display of the outdoor temperature. MANUAL SETTING: 12 / 24- HOUR TIME DISPLAY SETTING AND TEMPERATURE UNIT (°C/°F) SETTING User may choose to display the time in 12-hour or 24-hour mode: Note: When the time display is set as 12-hour mode, the temperature unit will be set to °F; when the time mode is in 24-hour format, the temperature unit will be set to °C. In normal display mode, press and hold the "set/ ch" key for about 3 seconds. The "12h" or "24h" digit will be flashing. Press the "min/max/+" key to set the desired time display mode. 55 3. Press shortly the "set/ ch" key to advance to the MANUAL TIME SETTING. MANUAL TIME SETTING User shall manually set the time of the Temperature Station by the following steps: 1. The hour digit of the time display will be flashing. Press the "min/max/+" key to adjust the hour (press and hold to allow fast advance). Press "set/ ch" key to confirm and go to the minute setting. [. . . ] User shall take an active part in the reuse, recycling and recovery of the electrical and electronic waste. The unrestricted disposal of electronic waste may do harm on public health and the quality of environment. As stated on the gift box and labeled on the product, reading the "User manual" is highly recommended for the benefit of the user. This product must however not be thrown in general rubbish collection points. [. . . ]