User manual LA CROSSE TECHNOLOGY WT-8005U-B

[. . . ] 5 About the Daily Alarms: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Automatic Snooze function: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 °F/°C Temperature Display:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Reception of the WWVB Radio signal: . . . . . . . . . . . . . . . [. . . ] Now use "" and "" buttons to turn Daylight Saving Time on ("on") or off ("oF"). See "Daylight Saving Time" below for more information. · Press "SET" to confirm your setting and to end the setting procedures, enter the clock mode. Daylight Saving Time · The National Institute of Standards and Technology and WWVB encode a special DST "bit" in the WWVB transmission for DST. · Your La Crosse Technology® clock will read this information (only if "DST" is set to "on" -) and automatically advance the time one hour in the spring and back an hour in the fall. · Arizona: If you live in an area that does not recognize DST you must de-activate Daylight Saving Time by setting "DST" to "oF" Setting the Time Zone: · Press the "" button to set the correct time zone. It will toggle the clock mode through the four available time zones in the Continental U. S. Above the seconds digits, the LCD display will indicate "P" for Pacific, "M" for Mountain, "C" for Central and "E" for Eastern. · After 30 seconds without pressing any button, the clock switches automatically from set mode to normal time mode. Setting the Daily Alarms: · To turn the alarm on, press the ALARM button. LCD displays the " " icon. Page 5 of 12 · To set the Alarm Time, press and hold down the ALARM button for 2 seconds until the hours digits flash. Use the "" and ""buttons to set the required hour. Press ALARM button to confirm your setting · The Minute display of the Alarm time starts to flash. Use the "" and ""buttons to set the required minute. Press ALARM button to confirm your setting and to end the setting procedure. · To activate or deactivate the daily alarms, briefly press the "ALARM" button once. When the alarm is active the clock displays the " " icon after the hour. When deactivated the alarm icon does not show. About the Daily Alarms: · After 30 seconds without pressing any button the clock switches automatically from setting mode to Normal clock mode. · The alarm will sound for 2 minutes if you do not deactivate it by pressing any button. In this case the alarm will be repeated automatically after 24 hours. · Rising alarm sound changes the frequency 4 times while the alarm signal is heard. This is known as a "Crescendo Alarm". Automatic Snooze function: · While the alarm is sounding, press the SNOOZE button to activate the snooze function. The " " icon appears on the display. · This operation moves the alarm back by 5 minutes and the alarm will restart at this time. · The Snooze function can be interrupted by pressing any button. Page 6 of 12 °F/°C Temperature Display: · The temperature is displayed either in °F or °C. Briefly pressing the " "button allows you to switch between the temperature modes. Reception of the WWVB Radio signal: · The clock must receive the WWVB Radio Signal to automatically set the time, date and weekday. · The clock automatically starts the WWVB signal search after 7 minutes of any restart or changing of new fresh batteries. The radio tower icon starts to flash. · At 1:00 am, the clock automatically carries out the synchronization procedure with the WWVB signal to correct any deviations to the exact time. If this synchronization attempt is unsuccessful (the radio tower icon disappears from the display), the system will automatically attempt another synchronization at the next full one hour. This procedure is repeated automatically up to total 5 times. · To start manual WWVB signal reception, press the "WWVB SEARCH" button. If no signals received within 7 minutes, then the WWVB signal search stops (the radio tower icon disappears) and will start again at the next full one-hour. · To cancel RC reception and stop searching for the WWVB radio signal, press the "WWVB SEARCH" button once. About WWVB Radio Signal Reception: · A flashing radio tower icon indicates that the WWVB signal reception has started. · A continuously displayed radio tower icon indicates that the WWVB signal was received successfully during the last attempt. If the clock attempts to receive the WWVB signal and Page 7 of 12 is unsuccessful, the tower icon will not be continuously displayed on the LCD. · We recommend a minimum distance of 2. 5 meters (8 feet) to all sources of interference, such as televisions or computer monitors · Radio reception is weaker in rooms with concrete walls (e. g. : in cellars) and in offices. In such environments, place the system close to the window. Online Resources · Visit the WT-8005U page online at: http://www. lacrossetechnology. com/8005 Care and Maintenance · Extreme temperatures, vibration and shock should be avoided as these may cause damage to the unit and give inaccurate readings. · Precautions shall be taken when handling the batteries. [. . . ] Some States do no allow the exclusion of consequential or incidental damages; therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information contact: Hours: Mon-Fri. ­ 8:00 AM to 6:00 PM Central e-mail: support@lacrossetechnology. com La Crosse Technology, Ltd 2817 Losey Blvd. La Crosse, WI 54601 Phone: 608. 782. 1610 Fax: 608. 796. 1020 For information on other La Crosse Technology® products, e-mail: sales@lacrossetechnology. com All rights reserved. [. . . ]