User manual LA CROSSE TECHNOLOGY WT292

[. . . ] The DCF reception tower at the top of the seconds will start flashing and the alarm times will be shown at the preset time of 6:00. The clock will now start receiving the DCF time signal. After approximate 3 to 5 minutes, the DCF time will be displayed. If reception is not successful within approximately 7-10 minutes, it will attempt to receive the signal in the next following hour (DCF time reception is every full hour). [. . . ] If the waiting time is too long, flashing will stop and the time can not be set any longer. In such case simply press the "AL/HR" key once again and the display will resume flashing. While the display is flashing: Set the hours and minutes of the desired alarm time by use of the "AL/HR" (hours) or the "AL/MIN" keys (minutes) respectively. (If the respective key is pressed permanently the hours setting will continuously advance by steps of 1 and the minutes setting by steps of 5). Once the alarm time is set, press the "SNOOZE/24HR AL/ " key to confirm or wait approximately 8 seconds (automatic exit of alarm time setting mode, AL 1 will stop flashing). To set alarm 2, repeat above steps but use the "AL/MIN" key. If both alarms are set for the same time then only alarm 2's sound will be heard. The date cannot be displayed when Alarm 2 setting is activated. Press and hold down the "AL/MIN" key, the AL2 icon will flash (if present) and the alarm on/off icon "(((2)))" (if present) will disappear. Press the "SNOOZE/24HR AL/ " key to confirm or wait approximately 8 seconds to exit. The date will appear in place of alarm 2 time setting. To return to alarm display, simply press the "AL/MIN " key again. The date can only be displayed with reception of DCF time and the calendar will change accordingly to DCF time from Frankfurt. ALARM SETTING: AL 1 (flashing) Hours setting Minutes setting TO CHANGE FROM ALARM 2 TO DATE DISPLAY: 1. Press the "AL/HR" key until (((1))) icon appears and the AL 1 icon on the LCD TO TURN ALARM OFF FOR 24 HRS WHEN IT IS RINGING (BOTH ALARM 1 OR 2): 1. Press the "SNOOZE/24HR AL/ " key to start the desired snooze time or press and hold until the confirmation tone sounds the "SNOOZE/24HR AL/ " key to switch the alarm off for 24 hours. Or, press the "AL/HR" key to stop alarm 1 or the "AL/MIN" key to stop alarm 2. This will turn the alarm off for 24 hours. TO REACTIVATE THE ALARM SETTING: Alarm 1: 1. In normal mode display, press the "AL/HR" key. The alarm icon "AL 1" will flash first, then the alarm on/off icon "(((1)))" will appear indicating that it has now been turned on. Press the "SNOOZE/24HR AL/ " key to exit this mode. In normal mode display, press the "AL/MIN" key. The alarm icon "AL 2" will flash first, then the alarm on/off icon "(((2)))" will appear indicating that it has now been turned on. [. . . ] This is because it activates from the start of next minute after the "SNOOZE" key was pressed ­ it does not count the current minute that it was pressed in. For example: if the alarm is set at 7:00 and 10 minutes snooze time is required so that when pressed it will go on again at 7:10, then 9 minutes has to be set as the snooze time. TIME ZONE SETTING: 0 = Central Europe Time zone To change to a different time zone (±9 hours): 1. Press and hold down the "SNOOZE/24HR AL/ " key to enter the time setting mode 2. Press the "SNOOZE/24HR AL/ " key once more, the time zone and snooze time setting will be displayed at the lower part of the LCD (Left digit = Time zone, right digit = Snooze) Snooze time To use the snooze feature, simply press the "SNOOZE/24HR AL/ " key when the alarm is sounding and the alarm will snooze for 5 minutes before automatically sounding again. [. . . ]