User manual LACIE 12BIG RACK FIBRE

[. . . ] LaCie 12big Rack Fibre User Manual Table of Contents page 1 Table of Contents 1. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LaCie 12big Rack Fibre RAID Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LaCie 12big Rack Fibre expansion Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] CAUTION: Handle the module carefully and avoid damaging the connector pins. Do not install the module if any pins appear to be bent. With the latches in the open position (see Fig. 41), slide the Disk I/O module into the enclosure until the latches engage. Secure the module by manually closing the latches. A click should be heard as the latches engage. Fig. 41 - Inserting the Disk I/O Module Fig. 42 - Securing the Disk I/O Module LaCie 12big Rack Fibre User Manual Getting Started page 37 2. 4. 6. Drive Carrier Module Disk drives are shipped installed in the enclosure with the anti-tamper locks engaged. To ensure the drives are installed correctly and follow the prescribed rules, refer to section 2. 8. 1. 43 - De-activating the Anti-tamper Lock 2. 4. 6. 1. If the anti-tamper lock is engaged, carefully insert the lock key provided into the cutout in the handle and into its socket. Rotate the key in a counter-clockwise direction until the "red" indicator is not visible in the aperture beside the key. Release the Drive Carrier module handle, by pressing the latch in the handle with your finger and rotating the handle towards the right (Fig. Gently withdraw the Drive Carrier module from the drive slot. Repeat for the remaining disk drives. Fig. 44 - Unlatching a Drive Carrier Module Fig. 45 - Removing a Drive Carrier Module LaCie 12big Rack Fibre User Manual Getting Started page 38 2. 4. 6. 2. Installing a Drive Carrier Module CAUTION: All drive slots must be fitted with Drive Carrier modules or Dummy Carrier modules to maintain a balanced air flow. IMPORTANT INFO: Ensure that the carrier is orientated so that the drive handle opens to the right. Release the carrier handle, by pressing the latch with your finger and rotating the handle towards the right. Insert the Drive Carrier module into an empty drive slot in the enclosure. Slide the Drive Carrier module, gently, all the way into the enclosure until it stops and seat it by pressing with your thumb on the left edge of the module (Fig. Secure the drive carrier by closing the handle until it fully engages. [. . . ] NEMA 5-15P grounding-type attachment plug rated 120V 10A; or IEC 320 C14, 250V, 10A. IEC 320 C-13, 250V, 10A. Europe and Others Cord Type Socket Harmonized, H05-VVF-3G1. 0. IEC 320 C-13, 250V, 10A. LaCie 12big Rack Fibre User Manual Standards & Regulations page 82 7. 6. EMC Precautions If passive copper cables are connected, the cable must not have a connection to a common ground/earth point. 7. 7. [. . . ]