User manual LACIE 12BIG RACK NETWORK

[. . . ] LaCie 12big Rack Network User Manual Table of Contents page 1 Table of Contents 1. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 The LaCie 12big Rack Network System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 The Enclosure Core Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 14 - Enclosure Rear View showing Switches and Connections NOTE: Please refer to Fig. 14 for details of the Ops Panel LEDs and related fault conditions. Follow the procedure below to Power On the enclosure. The Power Active LED on the Ops Panel should be lit (Green) when the enclosure power button is pressed (and the disk drive motors should start). IMPORTANT INFO: If mains power is lost for any reason, on restoration of power the enclosure will re-start automatically. 3. 2. 1. Power Supply Unit LEDs The PSU incorporates a bi-color Red/Green LED. When the PSU is connected to a mains supply the Green LED will flash. When the PSU is switched on the Green LED will be continuously illuminated. If a fault occurs the Red LED will be continuously illuminated. The Red LED will flash to signify Over Current, Under Voltage or Over Voltage Protection conditions. Power Supply LEDs and switches are shown in Fig. 14. LaCie 12big Rack Network User Manual Operation page 23 3. 3. Ops Panel LEDs and Switches The Ops Panel LEDs (Fig. 15) fault and status conditions are defined in Table 05 while the functions of the push-button switches are defined in Table 06. Troubleshooting & Problem Solving for details of any fault indication. Table 05 - Ops Panel LEDs LEDs Power Active Unit Fault Enclosure ID Status Constant Green: good or positive indication. Constant Amber: fault present Blue: only when activated Table 06 - Ops Panel Switches Push-button Switches On/Off Definition Fig. 15 - Ops Panel LEDs Function of this button is dependent on the enclosure status Enclosure connected to power source but not operating: Press button to activate and commence boot process Enclosure operating: Depress button for <4 seconds to shut down the enclosure System Reset Resets the enclosure hardware and firmware. Note: This button is recessed and is activated with a ball-point pen or similar implement. Enclosure ID LED Each press of this button causes the state of the blue ID LEDs on the Ops Panel and rear panel to change. LaCie 12big Rack Network User Manual Operation page 24 3. 4. Starting the Drives Unless otherwise selected during installation, all drives in the enclosure should automatically start their motors. If this has not occurred one of the following conditions may exist: There may be a power problem (an alarm and power fault indication would normally be active). If there is only one PSU present, the drive motors will spin up in a delayed sequence. Fig. 16 - Activating the Anti-tamper Lock 3. 4. 1. Disk Drive LEDs Each Drive Carrier module incorporates two LEDs, Upper (Green) and Lower (Amber), shown in Fig. In normal operation the Green LED will be ON and will flicker as the drive operates. [. . . ] 38 shows the ATX Reduced Rail Kit drawing which is included with the Rack Mounting Rail Kit and provides rail assembly details. Please contact LaCie for the latest issue of this drawing. continued on the next page >> A 01-A NH 25440 B C FIGURE 1 CLAMPING SCREWS LaCie 12big Rack Network User Manual D Fig. 38 - Rail Kit Installation Drawing REV 18/08/2006 5 1 E TAPPED HOLE RACK FRONT RACK POST F 4 2 G USE SAME SCREWS AND WASHERS ON FRONT AND REAR POSTS H 4 3 I ASSEMBLY INSTRUCTIONS 1. PERFORM THIS STEP ONLY IF INSTALLING INTO A TAPPED HOLE RACK:REMOVE THE NUT SHOWN IN FIGURE 1 USING THE SPANNER SUPPLIED. 2. ASSEMBLE (2x) ITEMS 6 (NOT HANDED) TO RIGHT AND LEFT SIDES OF RACK. J FIT THE LOCATION PIN AT THE REAR END OF RAIL ITEM 6 INTO THE REAR RACK POST. EXTEND THE RAIL TO FIT BETWEEN THE FRONT AND REAR RACK POSTS, ATTACH TO BOTH THE FRONT AND REAR OF RACK USING SCREW & WASHER COMBINATION: ROUND HOLE - ITEMS 3 AND 4, SQUARE HOLE - ITEMS 2 AND 4, TAPPED HOLE - ITEMS 1 AND 5 SCREWS SHOULD BE LEFT LOOSE ENOUGH TO ALLOW RAIL SIDEWAYS MOVEMENT ON ITS SLOTS. TIGHTEN (2x) CLAMPING SCREWS 3. MOUNTING CHASSIS INTO RACK. K LIFT CHASSIS AND ALIGN WITH RACK RAILS, CAREFULLY INSERT CHASSIS SLIDES INTO RACK RAILS AND PUSH FULLY HOME. [. . . ]